210-010問題集、VCE実際の試験問題

質問 1

What is the purpose of the EMC VNXe Connection Utility installed on the Vblock System 320 array management server?

A. to provision storage

B. to troubleshoot performance issues

C. to perform upgrades

D. to configure the management IP address

正解: D

質問 2

You are adding a new VLAN from the Cisco Nexus 1000V. You use the state enabled command.
What is the result of this command?

A. It creates a new VLAN in the Cisco fabric interconnects.

B. It creates a new VLAN in the Cisco Nexus 1000V.

C. It creates a new VMkernel port in the ESXi host.

D. It creates a port group in the vCenter server.

正解: D

質問 3

During a Vblock System 320 deployment, the customer wants to disassociate four half-width blades in a single chassis for a future project.
Which tool is used to perform this compute reconfiguration?

A. UCSM

B. vSphere

C. CIMC

D. Unisphere

正解: A

質問 4

What is a valid method to install EMC PowerPath/VE onto a VMware ESXi host?

A. Install using the rpowermt command.

B. Install from the PowerPath/VE vCenter plug-in.

C. Install using vCenter Update Manager (VUM).

D. Install remotely from the array management server.

正解: C

質問 5

A Vblock System 720 has been configured in the factory according to the VCE Logical Build Guide.
Which statement is correct?

A. Each service-profile should have at least one vHBA pinned to fabric interconnect A; one vHBA pinned to fabric interconnect B, and failover enabled.

B. Each service-profile should have at least one vHBA pinned to fabric interconnect A; one vHBA pinned to fabric interconnect B, and failover disabled.

C. Each service-profile should have at least one vNIC pinned to fabric interconnect A; one vNIC pinned to fabric interconnect B, and failover enabled.

D. Each service-profile should have at least one vNIC pinned to fabric interconnect A; one vNIC pinned to fabric interconnect B, and failover disabled.

正解: D

質問 6

Which protocol is used to provide unified file storage connectivity to a Vblock System 320?

A. FC

B. iSCSI

C. IP

D. FCoE

正解: C

質問 7

What information is displayed when an administrator uses the show vsan membership command on a Cisco MDS switch?

A. information for a specific VSAN

B. membership information for a specified VSAN

C. membership information for all VSANs

D. zone database information for a specific VSAN

正解: C

質問 8

During a Vblock System 200 deployment, a single server did not power on and a replacement has been received.
Which management interface is used to prepare the server for installation?

A. UCSM

B. vSphere

C. CIMC

D. Unisphere

正解: C

質問 9

A customer would like to add a new production VLAN to their Vblock System with UIM/P. The VLAN was added to the UIM/P service profile, and the connected Cisco Nexus 5000. The customer is still not able to use the new VLAN with a virtual machine.
Which step must the customer complete?

A. Add the VLAN to Cisco Nexus 1000V.

B. Add the VLAN to Cisco Catalyst 3560.

C. Disable spanning tree on UCS.

D. Create a new VSAN.

正解: A

質問 10

Customers provide the information used to develop the Logical Configuration Survey (LCS) before manufacturing begins.
What information is required? (Choose two.)

A. NTP server IP address

B. syslog server IP address

C. MIB browser IP address

D. method of device access (telnet or SSH)

正解: A,D

VCE Vblock Systems Deployment and Implementation - Core - 210-010 模擬練習