Fortinet FCSS - Network Security 7.6 Support Engineer - FCSS_NST_SE-7.6 模擬練習
Exhibit.
Refer to the exhibit, which shows the output of diagnose automation test.
What can you observe from the output? (Choose two.)
Refer to the exhibit, which shows the output of diagnose automation test.
What can you observe from the output? (Choose two.)
正解: A,C
Refer to the exhibit, which shows the output of a BGP debug command.
What can you conclude about the router in this scenario?
What can you conclude about the router in this scenario?
正解: C
解説: (PassTest メンバーにのみ表示されます)
Refer to the exhibit, which shows a partial output from the get router info routing-table database command.
The administrator wants to configure a default static route for port3 and assign a distance of 50 and a priority of 0.
What will happen to the port1 and port2 default static routes after the port3 default static route is created?
The administrator wants to configure a default static route for port3 and assign a distance of 50 and a priority of 0.
What will happen to the port1 and port2 default static routes after the port3 default static route is created?
正解: C
A VPN tunnel is up. To monitor traffic flow, the administrator enters the following CLI commands on an SSH session on FortiGate:
# diagnose debug enable
# diagnose sniffer packet any 'udp and port 500' 4
However, the sniffer does not show any output. Assuming default configuration values, what are two possible reasons there is no output? (Choose two answers)
# diagnose debug enable
# diagnose sniffer packet any 'udp and port 500' 4
However, the sniffer does not show any output. Assuming default configuration values, what are two possible reasons there is no output? (Choose two answers)
正解: A,C
解説: (PassTest メンバーにのみ表示されます)
Refer to the exhibit, which shows the partial output of a real-time OSPF debug.
Why are the two FortiGate devices unable to form an adjacency?
Why are the two FortiGate devices unable to form an adjacency?
正解: B
What is an accurate description of LDAP authentication using the regular bind type?
正解: C
解説: (PassTest メンバーにのみ表示されます)
Refer to the exhibits.
FGT-1 is an area border router (ABR) that has interfaces in OSPF areas 0.0.0.0 and 0.0.0.5. FGT-3 acts as an autonomous system border router (ASBR), importing static routes into OSPF. FGT-2 is an internal router with all its interfaces belonging to area 0.0.0.5. FGT-1 is receiving all advertised routes from FGT-2, however, FGT-3 is not receiving any of the advertised routes from FGT-1. What is the most likely reason for this? (Choose one answer)
FGT-1 is an area border router (ABR) that has interfaces in OSPF areas 0.0.0.0 and 0.0.0.5. FGT-3 acts as an autonomous system border router (ASBR), importing static routes into OSPF. FGT-2 is an internal router with all its interfaces belonging to area 0.0.0.5. FGT-1 is receiving all advertised routes from FGT-2, however, FGT-3 is not receiving any of the advertised routes from FGT-1. What is the most likely reason for this? (Choose one answer)
正解: C
解説: (PassTest メンバーにのみ表示されます)
What are two reasons you might see iprope_in_check() check failed, drop when using the debug flow? (Choose two.)
正解: A,C
解説: (PassTest メンバーにのみ表示されます)
Exhibit.
Refer to the exhibit, which shows a partial output of diagnose hardware aysinfo memory.
Which two statements about the output are true? (Choose two.)
Refer to the exhibit, which shows a partial output of diagnose hardware aysinfo memory.
Which two statements about the output are true? (Choose two.)
正解: B,C
解説: (PassTest メンバーにのみ表示されます)