HP2-Z18問題集、HP実際の試験問題

質問 1

You make configuration changes to the running configuration of your HP E3500 yI switch. Which command saves these changes to your startup configuration?

A. write memory

B. copy running-config startup-config

C. write config

D. save running-config

正解: A

質問 2

What is the default load-balancing behavior for Layer 2 traffic forwarded over aggregated links on an HP A-Series switch?

A. Load-balancing is based on the source MAC address and the destination MAC address.

B. Load-balancing is based on the destination MAC address only.

C. Load-balancing is based on the source MAC address and egress port

D. Load balancing is based on the source MAC address only.

正解: A

質問 3

Refer to the exhibit below.

Given this configuration on an HP A-Series switch, which command is required to enable administrator level privileges?

A. super password level 3 [simple|cipher] password

B. set administrator level password [simple|cipher] password

C. privilege 3 password [simple|cipher] password

D. local-user admin1 level3

正解: A

質問 4

What are benefits of implementing Secure Socket Shell (SSH) for remote management of HP switches? (Select two)

A. user accounting

B. encryption of all traffic

C. stronger passwords

D. encryption of management traffic

E. enforcement of management VLAN

F. secure authentication

正解: D,F

質問 5

Which upgrade method enables an administrator to upload a new application file to an MSR Series router located in a remote site?

A. USB flash drive

B. XModem

C. Boot Menu

D. TFTP/FTP

正解: D

質問 6

Which command will configure an HP A-Series switch to be the Root Bridge in MST instance 1?

A. [Switch] mstp root instance 1

B. [Switch] stp instance 1 priority root

C. [switch] stp instance 1 root primary

D. [Switch] spanning-tree instance 1 priority 0

正解: C

質問 7

Which link aggregation protocol is supported by HP A-Series switches?

A. HP Port Trunking

B. Link Aggregation Control Protocol (LACP)

C. Multi-Link Trunking (MLT)

D. Port Aggregation Protocol (PAgP)

正解: B

質問 8

You have enabled IP routing on an-HP E8212 zI switch. You must configure the switch so that all packets with destination addresses not in its routing table are forwarded to 192.111.254.1. Which command accomplishes this task?

A. E8212 (config) # ip route 0.0.0.0/0 192.111.254.1

B. E8212 (config)# ip route 255.255.255.255 192.111.254.1

C. E8212 (config)# ip default-route 192.111.254.1

D. E8212 (config) # ip helper 192.111.254.1/24

正解: A

質問 9

Port B1 on an HP ProCurve 5406zI switch is an untagged member of VLAN 155 and not a tagged member of any VLAN PortC1is a tagged member of VLAN 155 and an untagged member of VLAN
100. You issue the following command:
5406zl (config)# no vlan 155
Why do you receive the following prompt?
The following ports will be moved to the default VLAN:
Bl
Do you want to continue? [y/n]:

A. The CLI will not allow you to orphan a port

B. The CLI will not delete a VLAN with any port membership.

C. The CLI always issues this prompt when deleting a VLAN

D. All ports must be moved to the default VLAN before you can delete the VLAN.

正解: D

質問 10

You are the network administrator at a company with multiple remote sites. You are using HP ProCurve Manager Plus (PCM+) to manage network devices in all of the company's offices. How can PCM+ remote agents help manage your network?

A. They detect unauthorized PCM+ servers and quarantine unauthorized switches and hubs.

B. They detect unauthorized PCM+ servers and clients.

C. They enforce policies defined on the PCM+ server and discover manageable devices.

D. They manage access by remote clients and coordinate communications across subnets.

正解: C

HP Network Infrastructure AIS 2011 - HP2-Z18 模擬練習