NS0-516問題集、Network Appliance実際の試験問題

質問 1

You are setting up asynchronous mirroring between two E2860 systems.
In this scenario, which two prerequisites are required to complete the setup? (Choose two.)

A. The secondary system must have 2X the storage capacity of the primary system.

B. Both the primary and secondary systems must be using the same subnets for mirroring connections.

C. Both the primary and secondary systems must have the same premium features licensed.

D. Both systems must be discovered by an Enterprise Management Window (EMW) or SANtricity Unified Manager.

正解: C,D

解説: (PassTest メンバーにのみ表示されます)

質問 2

A junior administrator recently made changes to an E-Series system. As a result of these changes, the management host lost the ability to manage the E-Series system through in-band management, but the host still has access to the E-Series data volumes.
In this scenario, what caused this issue?

A. The ownership of the management host's volumes changed

B. Auto Load Balancing was disabled

C. The access volume was un-mapped

D. The management IPs were changed

正解: C

解説: (PassTest メンバーにのみ表示されます)

質問 3

Which iSCSI setting would you change from its default value to increase the throughput of an iSCSI host port on a NetApp E-Series system?

A. flow control

B. maximum transmission unit (MTU)

C. Challenge-Handshake Authentication Protocol (CHAP)

D. Time to Live (TTL)

正解: B

解説: (PassTest メンバーにのみ表示されます)

質問 4

What are two methods for setting the host protocol configuration on the E2800 controller with a 4-port 16Gbps FC or 10Gbps iSCSI SFP+ host interface card (HIC)? (Choose two.)

A. Set at the factory, based on the order

B. Change the QSFP type in the HIC

C. Set in the Hardware tab using SANtricity System Manager

D. Change the Feature Pack in the SANtricity System Manager

正解: A,C

解説: (PassTest メンバーにのみ表示されます)

質問 5

You are cabling drive expansion shelves for an E2800 storage system.
In this scenario, which cabling method should you use?

A. You use SAS expansion port EXP1 and reserve SAS expansion port EXP2 for a second drive expansion stack.

B. The controller A and the controller B SAS expansion ports (EXP1 & EXP2) should not be divided between the A-side and B-side IOM-12 modules for all of the expansion shelves.

C. The controller A and the controller B SAS expansion ports (EXP1 & EXP2) should be divided between the A-side and B-side IOM-12 modules for all the expansion shelves.

D. You use SAS expansion port EXP2 and reserve SAS expansion port EXP1 for a second drive expansion stack.

正解: C

解説: (PassTest メンバーにのみ表示されます)

質問 6

To enable one-way authentication in a new iSCSI Linux implementation, which three modifications should you make in the /etc/iscsi/iscsid.conf file on the Linux host? (Choose three.)

A. sendtargets discovery

B. iSCSI

C. the target username and password

D. the initiator username and password

E. CHAP

正解: C,D,E

解説: (PassTest メンバーにのみ表示されます)

質問 7

Which command will display which Brocade switches are connected into a fabric?

A. configshow

B. fabricshow

C. show fabric

D. switchshow

正解: B

解説: (PassTest メンバーにのみ表示されます)

Network Appliance NetApp Implementation Engineer SAN Specialist E-Series (NCIE) - NS0-516 模擬練習