結果を保証するには最新2025年06月無料Fortinet NSE5_FMG-7.2で練習しよう
有効な問題最新版を無料で試そうNSE5_FMG-7.2試験問題集解答
質問 # 36
Refer to the exhibit.
A junior administrator is troubleshooting a FortiManager connectivity issue that rs occurring with managed FortiGate devices Given the FortiManager device manager settings shown in the exhibit what can you conclude from the exhibit?
- A. The administrator had restored the FortiManager configuration file
- B. FortiManager test internet connectivity therefore, both devices appear to be down
- C. The administrator must refresh both devices to restore connectivity
- D. The administrator can reclaim the FGFM tunnel to get both devices online
正解：D
質問 # 37
An administrator would like to create an SD-WAN using central management in theTrainingADOM.
To create an SD-WAN using central management, which two steps must be completed? (Choose two.)
- A. Enable SD-WAN central management in theTrainingADOM
- B. Specify a gateway address when you create a default SD-WAN static route
- C. Configure and install the SD-WAN firewall policy and SD-WAN static route before installing the SD-WAN template settings
- D. Remove all the interface references such as routes or policies that will be a part of SD-WAN member interfaces
正解：A、D
解説：
Reference:https://docs.fortinet.com/document/fortigate/6.0.0/cookbook/676493/removing-existing-configuration
質問 # 38
An administrator run the reload failure command: diagnose test deploymanager reload config
<deviceid> on FortiManager. What does this command do?
- A. It installs the latest configuration on the specified FortiGate and update the revision history database.
- B. It downloads the latest configuration from the specified FortiGate and performs a reload operation on the device database.
- C. It compares and provides differences in configuration on FortiManager with the current running configuration of the specified FortiGate.
- D. It installs the provisioning template configuration on the specified FortiGate.
正解：B
質問 # 39
An administrator is replacing a device on FortiManager by running the following command:
execute device replace sn <devname> <serialnum>.
What device name and serial number must the administrator use?
- A. Device name and serial number of the replacement device.
- B. Device name of the replacement device and serial number of the original device.
- C. Device name and serial number of the original device.
- D. Device name of the original device and serial number of the replacement device.
正解：D
質問 # 40
Refer to the exhibit.
Given the configuration shown in the exhibit, which two statements are true? (Choose two.)
- A. It is used to validate administrator login attempts through external servers.
- B. It allows the same administrator to lock more than one ADOM at the same time.
- C. It disables concurrent read-write access to an ADOM.
- D. It allows two or more administrators to make configuration changes at the same time, in the same ADOM.
正解：B、D
質問 # 41
Refer to the exhibit.
An administrator logs into the FortiManager GUI and sees the panes shown in the exhibit.
Which two reasons can explain why the FortiAnalyzer feature panes do not appear? (Choose two.)
- A. FortiAnalyzer features are not enabled on FortiManager.
- B. The administrator logged in using the unsecure protocol HTTP, so the view is restricted.
- C. The administrator profile does not have full access privileges like the Super_User profile.
- D. The administrator IP address is not a part of the trusted hosts configured on FortiManager interfaces.
正解：A、C
質問 # 42
Refer to the exhibit.
According to the error message why is FortiManager failing to add the FortiAnalyzer device?
- A. The administrator must use the correct user name and password of the FortiAnalyzer device
- B. The administrator must use the Add Model Device section and discover the FortiAnalyzer device
- C. The administrator must turn off the Use Legacy Device login and add the FortiAnalyzer device to the same network as Forti-Manager
- D. The administrator must select the Forti-Manager administrative access checkbox on the FortiAnalyzer management interface
正解：C
質問 # 43
What does a policy package status of Never Installed indicate?
- A. FortiManager is unable to determine the policy package status.
- B. The policy configuration has been changed on a managed device and changes have not yet been imported into FortiManager.
- C. The policy package was never imported after a device was registered on FortiManager
- D. The policy configuration has been changed on FortiManager and changes have not yet been installed on the managed device.
正解：C
解説：
Never Installed: There is no policy package for this unit. Either policies and objects have not been imported yet or no policy package has been assigned for this unit. https://community.fortinet.com/t5/FortiManager/Technical-Tip-FortiManager-policy-package-installation-and/ta-p/195923
質問 # 44
Refer to the exhibit.
An administrator has created a firewall address object that is used in multiple policy packages for multiple FortiGate devices in an ADOM.
After the installation operation is performed, which IP/netmask will be shown on FortiManager for this firewall address object without specify Per-Device Mapping?
- A. The FortiManager replaces the address object to none.
- B. 0.0.0.0/0.
- C. 10.0.5.0/24.
- D. 192.168.1.0/24.
正解：D
解説：
In the scenario you described, an administrator has created a firewall address object used in multiple policy packages for multiple FortiGate devices within an Administrative Domain (ADOM) on FortiManager. The question concerns the display of this object's IP/netmask in FortiManager after installation, assuming no per-device mapping is specified.
Given the screenshot and the description of the situation, the answer is **C. 192.168.1.0/24**. When you create a firewall address object in FortiManager without specifying per-device mapping, FortiManager uses the generic settings of the object as defined. In the screenshot, the IP/Netmask is set to 192.168.1.0/255.255.255.0, and since there is no per-device variation defined or required in your query, this setting remains as shown in the object's configuration.
質問 # 45
What will happen if FortiAnalyzer features are enabled on FortiManager?
- A. FortiManager can be used only as a logging device.
- B. FortiManager will enable ADOMs automatically to collect logs from non-FortiGate devices
- C. FortiManager will reboot
- D. FortiManager will send the logging configuration to the managed devices so the managed devices will start sending logs to FortiManager
正解：C
質問 # 46
An administrator has enabled Service Access on FortiManager.
What is the purpose of Service Access on the FortiManager interface?
- A. Allows FortiManager to download IPS packages
- B. Allows FortiManager to automatically configure a default route
- C. Allows FortiManager to respond to request for FortiGuard services from FortiGate devices
- D. Allows FortiManager to run real-time debugs on the managed devices
正解：C
質問 # 47
Refer to the exhibit.
You ate using the Quick install option to install configuration changes on the managed FortiGate Which two statements correctly describe the result? (Choose two)
- A. It install provisioning template changes on the FortiGate device
- B. It provides the option to preview only the policy package changes before installing them
- C. It installs device-level changes on the FortiGate device without launching the Install Wizard
- D. It installs all the changes in the device database first and the administrator must reinstall the changes on the FodiGate device
正解：A、C
質問 # 48
Which of the following statements are true regarding schedule backup of FortiManager? (Choose two.)
- A. Does not back up firmware images saved on FortiManager
- B. Can be configured from the CLI and GUI
- C. Backs up all devices and the FortiGuard database.
- D. Supports FTP, SCP, and SFTP
正解：A、D
質問 # 49
An administrator run the reload failure command:diagnose test deploymanager reload config
<deviceid>on FortiManager. What does this command do?
- A. It installs the latest configuration on the specified FortiGate and update the revision history database.
- B. It downloads the latest configuration from the specified FortiGate and performs a reload operation on the device database.
- C. It compares and provides differences in configuration on FortiManager with the current running configuration of the specified FortiGate.
- D. It installs the provisioning template configuration on the specified FortiGate.
正解：B
解説：
Reference:https://community.fortinet.com/t5/FortiManager/Technical-Note-Retrieve-configuration-file-using-CL
質問 # 50
What is the purpose of thePolicy Checkfeature on FortiManager?
- A. To find and provide recommendation to combine multiple separate policy packages into one common policy package
- B. To find and merge duplicate policies in the policy package
- C. To find and provide recommendation for optimizing policies in a policy package
- D. To find and delete disabled firewall policies in the policy package
正解：C
解説：
Reference:https://help.fortinet.com/fmgr/50hlp/56/5-6-2/FortiManager_Admin_Guide/1200_Policy%20and%20O
質問 # 51
Refer to the exhibit.
What can you conclude from the failed installation log shown in the exhibit?
- A. Policy ID 2 is installed in the disabled state.
- B. Policy ID 2 is installed without a source address.
- C. Policy ID 2 will not be installed.
- D. Policy ID 2 is installed without the remote user student.
正解：D
質問 # 52
Refer to the exhibit.
Which statement about the object named ALL is true?
- A. FortiManager updated the object ALL using the FortiGate value in its database.
- B. FortiManager created the object ALL as a unique entity in its database, which can be only used by this managed FortiGate.
- C. FortiManager installed the object ALL with the updated value.
- D. FortiManager updated the object ALL using the FortiManager value in its database.
正解：A
質問 # 53
Refer to the exhibit.
Given the configuration shown in the exhibit, which two statements are true? (Choose two.)
- A. The FortiManager ADOM workspace mode is set to Normal.
- B. FortiManager is in workflow mode.
- C. The FortiManager ADOM is locked by the administrator.
- D. An administrator can also lock the Local-FortiGate-1 policy package.
正解：C、D
質問 # 54
......
NSE5_FMG-7.2ブレーン問題集PDF、Fortinet NSE5_FMG-7.2試験問題詰合せ：https://www.passtest.jp/Fortinet/NSE5_FMG-7.2-shiken.html
2025年最新のNSE5_FMG-7.2サンプル問題は信頼され続けるNSE5_FMG-7.2テストエンジン：https://drive.google.com/open?id=1kUuwDKrGfKyAeUAaWSdF758bvVsfoDcW