2023年最新ののNetwork Appliance NS0-176問題集PDFNS0-176最速合格したいならここ
NS0-176練習試験問題集で99%合格率Network Appliance試験合格させます
質問 69
You are asked to install the Virtual Supervisor Module (VSM) software on a Nexus 1000v switch.
Which two sources would you use to install this software? (Choose two.)
- A. VSC plug-in
- B. PXE boot
- C. ISO image
- D. OVA file
正解: B,C
質問 70
Which statement is true about NFS exports in Clustered Data ONTAP?
- A. Exports can be either persistent or temporary.
- B. Export policies and rules need to be set at the data Vserver level and export policies are created and modified by editing /etc/exports on the node with the share.
- C. Export policies and rules need to be set at the data Vserver level.
- D. Export policies are created and modified by editing /etc/exports on the node with the share.
- E. Exports can be either persistent or temporary, and export policies and rules need to be set at the data Vserver level.
正解: C
質問 71
You are installing a FlexPod Express solution with a NetApp AFF A250 at a customer's remote site.
In this scenario, which two devices are required to provide an NFS v3 datastore? (Choose two.)
- A. NetApp BES-53248 Switches
- B. Cisco UCS 6454 Fabric Interconnects
- C. Cisco Nexus 3000 Switches
- D. Cisco UCS 6324 Fabric Interconnects
正解: C,D
質問 72
Which three are true for UCS 2208XP? (Choose three)
- A. Has 32 10Gb ports to each half-width slot in the chassis
- B. Supports native FC
- C. Connects to both Fabric Interconnects for high availability
- D. Supports 4 port port-channel toward FI 6140
- E. Supports FCoE
- F. Works with FI 6120 and FI 6296
正解: A,E,F
質問 73
Your UCS environment has recently been upgraded to include UCS B-Series Servers, UCS C-Series Servers, a UCS mini, and a fourth UCS domain. With these new changes, you need a management tool to help you manage the entire environment from a single location.
In this scenario, which tool would you use?
- A. UCS Central
- B. UCS Director
- C. UCS Manager
- D. Cisco Smart Advisor
正解: A
質問 74
After deploying a FlexPod solution, which tool would you use to validate a successful installation?
- A. UCS Manager
- B. System Manager
- C. Config Advisor
- D. Hardware Universe
正解: C
質問 75
Exhibit:
Referring to the exhibit, what do the asterisks on the left indicate about the output of the ~show zoneset active~ command?
- A. A redundant path is present.
- B. The device is not currently logged in.
- C. Only a single path is present.
- D. The device is currently logged in.
正解: D
質問 76
When trying to configure a Virtual Port Channel (vPC), what might be a cause of the following error when trying to create the vPC domain?
Nexus-5548-B(config)# vpc domain 10
^% Invalid command at '^' marker.Nexus-5548-B(config)#
- A. Have not yet turned on the vpc feature using the 'feature vpc' command
- B. The vPC links have to be configured before the vPC domain can be added
- C. vPC domain cannot be configured at the global prompt
- D. The vPC domain has already been configured
正解: A
質問 77
You are asked to create an interface group on a NetApp clustered Data ONTAP system. The system is connected to a Cisco Nexus switch in a vPC configuration with the port-channel mode set to active.
Which NetApp interface group made matches this switch configuration?
- A. multimode_lacp
- B. mode active
- C. singlemode
- D. multimode
正解: C
質問 78
Which server role is required to support running virtual machines on a Microsoft based hypervisor?
- A. Application Server
- B. Hyper-V
- C. Web Server
- D. Remote Access
正解: B
質問 79
Your company is looking for a small remote office infrastructure to deploy to your 30 remote sites. You are asked to write deployment procedures for each site. Your goal is to have each site deployed in less than a day.
Which tool will help you accomplish your goal?
- A. UCS Director
- B. UCS Manager
- C. OnCommand System Manager
- D. OnCommand Insight
正解: A
質問 80
Which policy detail should be set if you want a server to be exempt from all power capping?
- A. Create a Power Group with the appropriate chassis and set the Group Budget Power Cap (W) to 0.
- B. Create a Power Control Policy and set Power Capping to No Cap
- C. The UCS Power Cap feature should not be utilized in a FlexPod environment.
- D. Create a Power Control Policy select cap and set the priority to 1
正解: B
質問 81
How should the speed be configured on the Nexus 5548 port connecting to the Nexus 1100-X?
- A. It should not be configured - the 5548 will auto detect the correct speed
- B. Speed 10
- C. Speed 1000
- D. Speed 1G
- E. Speed 1000000
正解: C
質問 82
Which backup type stores Service Profile information as a small editable file?
- A. System Configuration
- B. Logical Configuration
- C. Full Backup
- D. All Configurations
正解: B
質問 83
Which four items are required in order to create a Gold Master Boot LUN to automate the provisioning of Hyper-V hosts using the built-in LUN cloning capabilities of NetApp storage? (Choose four.)
- A. Create additional virtual fibre channel (vfc) interfaces for the Nexus 5500
- B. Creation of a LUN for the Gold Master Boot LUN
- C. Creation of a service profile and zoning for Gold Master Boot LUN
- D. Configuration of the Server OS and hotfix installation
- E. SysPrep of the server operating system
- F. Create a new interface group on the NetApp Cluster
正解: B,C,D,E
質問 84
You are deploying a new virtual machine (VM). Your customer requires that the VM cannot reserve space on the VMFS filesystem, and the VM can only consume blocks when data is written to disk from and within the VM/Guest OS.
Which virtual disk should you create to meet these requirements?
- A. Thick Provision Eager Zeroed
- B. Thin Provision
- C. Thick Provision Lazy Zeroed
- D. Independent Nonpersistent
正解: B
質問 85
Which two are required for single-wire management for Cisco UCS C-Series? (Choose two)
- A. FI 6200 family only
- B. VIC 1240
- C. UCS Manager 2.1 or higher
- D. 10 GB LOM
- E. VIC 1225
- F. Redundant Nexus 2232PP FEX
正解: C,E
質問 86
What is the correct flow control setting for the intercluster ports on a NetApp cluster?
to 50% cashback.
- A. switched cluster = none switchless cluster = none
- B. switched cluster = none switchless cluster = full
- C. switched cluster = set to match the setting on switch port switchless cluster = none
- D. switched cluster = full switchless cluster = none
正解: C
質問 87
You installed a new NetApp cluster running clustered Data ONTAP. There is a single Storage Virtual Machine (SVM) named esx1 on the cluster.
A volume named esx_datastore1 is created in the SVM esx1. The name of the root volume for the esx1 SVM is esx1_rootvol. The default export policy was applied to the volume esx1_rootvol.
You verified that the export policy applied to esx_datastore1 contains a single rule that allows all clients to mount the volume as read/write using any version of NFS. A Linux client attempts to NFS mount the volume and receives a Permission Denied error.
In this scenario, what caused this error?
- A. NFS has not been configured on the SVM esx1.
- B. The default export-policy does not have at least one rule to allow all clients read-only access.
- C. The volume esx_datastore1 has not been mounted into the namespace of the esx1 SVM.
- D. UNIX permissions for the volume esx1_rootvol are not set to read/write.
正解: B
質問 88
An administrator is configuring a Flexpod Datacenter solution. The UCS service profiles will use FCoE connectivity to the NetApp cluster.
Which pool is needed to configure the vHBA templates?
- A. IQN pool
- B. WWPN pool
- C. WWNN pool
- D. MAC pool
正解: B
質問 89
You are asked to verify your MPIO settings for your ONTAP FlexPod solution. You are using VMware ESXi 6 and FCP as the storage protocol.
In this scenario, which MPIO setting would you use on the ESXi host?
- A. most recently used
- B. fixed path with array preference
- C. fixed path
- D. round robin
正解: D
質問 90
Which set of commands maps VLAN 100 to VSAN 100?
- A. Nexus 5000-A#configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-A (config)# vsan 100 Nexus 5000-A (config-vsan) # fcoe vsan 100
- B. Nexus 5000-A#configure terminal Nexus 5000-A (config) # vlan 100 Nexus 5000- A (config-vlan_ #fcoe vsan 100
- C. Nexus 5000-B# configure terminal Nexus 5000-B(config-vsan) # vlan 100 Nexus 5000-B (config-vsan)# vsan 100 name vsan100
- D. Nexus 5000-B# configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-B (config-vsan)# vsan 100 Nexus 5000-B(config- vsan) #vsan 100 name FCoE-VLAN 100
正解: B
質問 91
......
最新の検証済みNS0-176問題と解答で合格保証：https://www.passtest.jp/NetworkAppliance/NS0-176-shiken.html