[2025年08月]更新の2V0-11.25問題集には100%厳密検証された問題と解答で合格保証もしくは全額返金 [Q44-Q69]

[2025年08月]更新の2V0-11.25問題集には100%厳密検証された問題と解答で合格保証もしくは全額返金

合格させるVMware 2V0-11.25試験には練習テスト問題集豪華お試しセット

質問 # 44
An organization has experienced performance issues and requires a detailed analysis of infrastructure performance, capacity, utilization, and compliance using VMware Aria components.
What three steps should be followed to generate and analyze these reports? (Choose three.)

• A. Run predefined reports on capacity and utilization
• B. Create custom dashboards to monitor performance metrics
• C. Access Aria Operations and navigate to the Reports section
• D. Export the reports for further analysis and compliance verification
• E. Use Aria Operations for Logs to correlate log data with performance

正解：A、B、E

解説：
Creating custom dashboards in Aria Operations allows administrators to visualize and monitor performance metrics specific to the organization's needs, making it easier to analyze the infrastructure.
Using Aria Operations for Logs helps correlate log data with performance issues, enabling a deeper analysis and understanding of the root causes of performance problems.
Running predefined reports on capacity and utilization provides valuable insights into how resources are being consumed, helping identify areas that need optimization or adjustment.

質問 # 45
During a routine check, an administrator observes that several VMs are reporting high memory usage in VMware Aria Operations. They need to verify if the high memory usage is due to memory contention.
What actions should be taken in VMware Aria Operations to verify this?

• A. Review the CPU ready time.
  B Look al the network throughput
• B. Analyze the storage I/O performance.
• C. Check the memory usage and ballooning metrics.

正解：B

解説：
To verify if high memory usage is due to memory contention, the administrator should check the memory usage and ballooning metrics in VMware Aria Operations. Ballooning occurs when the hypervisor reclaims memory from a virtual machine due to memory contention, and monitoring these metrics can help identify whether the VMs are experiencing memory pressure or being forced to swap memory.

質問 # 46
While deploying the first VI workload domain in a VMware Cloud Foundation (VCF) solution, which two steps will always be performed by SDDC Manager? (Choose two.)

• A. Configure vSAN as a principal storage for the VI workload domain.
• B. Deploy an NSX Edge cluster and configure BGP routing on the T0 Gateway.
• C. Connect a new vCenter Server instance to the Application Virtual Network.
• D. Deploy and configure a new vCenter Server instance for the VI workload domain.
• E. Deploy a new NSX Manager instance for the VI workload domain.

正解：D、E

解説：
SDDC Manager always deploys a dedicated NSX Manager instance and a new vCenter Server for each VI workload domain during initial deployment.

質問 # 47
A cloud administrator recently deployed a new VI workload domain. As part of the initial VI domain creation, the administrator created a new SSO domain. However, they reconsidered and now want the domain to use the same SSO domain as the management domain.
How can the VI domain be changed from a dedicated SSO domain to sharing the SSO domain with the management domain?

• A. From the Management Domain vCenter Server instance, use the rsautil command to add the VI workload domain to the management domain SSO ring.
• B. From the SDDC Manager console, use the rsautil command to add the VI workload domain to the management domain SSO ring.
• C. The vSphere SSO domain cannot be changed once it has been deployed and a new VI workload domain that is part of the Management SSO domain must be created, and workloads migrated.
• D. From the VI Workload Domain vCenter Server instance, use the rsautil command to join the management domain SSO ring.

正解：C

解説：
Once the vSphere Single Sign-On (SSO) domain is set up for a workload domain, it cannot be changed. If you need the VI workload domain to use the same SSO domain as the management domain, you must create a new VI workload domain that is part of the management domain's SSO ring, and then migrate the workloads to the new domain.

質問 # 48
The administrator of a VMware Cloud Foundation environment notices that log data from multiple components, including vSphere, NSX, and vSAN, is not being collected properly in Aria Operations for Logs.
What two steps should the administrator perform to resolve this issue? (Choose two.)

• A. Reconfigure the log level settings on all vSphere components to ensure detailed logging.
• B. Ensure that the syslog configuration on each ESXi host is pointing to the correct Aria Operations for Logs server.
• C. Increase the storage capacity of the Aria Operations for Logs server to accommodate more log data.
• D. Check the network connectivity between the Aria Operations for Logs server and the VMware Cloud Foundation components.
• E. Verify that the Aria Operations for Logs license is still valid and active.

正解：B、D

解説：
Ensuring network connectivity between the Aria Operations for Logs server and VMware Cloud Foundation components is crucial. If there are network connectivity issues, logs may fail to be transmitted to the Aria Operations for Logs server.
The syslog configuration on each ESXi host must be set correctly to point to the Aria Operations for Logs server to ensure that log data from ESXi hosts is collected and sent to the log management system.

質問 # 49
An Administrator is configuring the network within their VCF management domain in preparation to deploy VMware Aria Suite Lifecycle.
What are the two types of virtual networks that the Administrator could configure to support the deployment? (Choose two.)

• A. VXLAN-backed Network Pools
• B. Overlay-backed NSX Segments
• C. VLAN-backed NSX Segments
• D. VLAN-backed Port Groups

正解：B、D

解説：
VLAN-backed Port Groups are used in traditional network environments where VLANs are configured on the physical switches. These port groups can be configured in the management domain to support network connectivity.
Overlay-backed NSX Segments use NSX to create virtual networks overlaid on existing physical networks, which is essential for network virtualization and communication between virtual machines, especially in a VMware Cloud Foundation environment.

質問 # 50
An administrator is using VMware Aria Automation to automate the provisioning of virtual machines in their VMware Cloud Foundation (VCF) environment. They notice that the deployment requests are failing frequently.
What step should the administrator take in VMware Aria Operations for Logs to diagnose the cause of the failures?

• A. Review the Alert Definitions to ensure alerts for request failures are configured and enabled.
• B. Check the Audit Logs to see if there are any unauthorized access attempts.
• C. Use the Interactive Analytics feature to search for error messages related to the requests.
• D. Access the Dashboard page to get an overview of system health and performance metrics.

正解：C

解説：
Using Interactive Analytics in Aria Operations for Logs lets you query and filter log data for specific error messages tied to provisioning requests, pinpointing the root cause of failures.

質問 # 51
What is a symptom of an issue with vSphere HA?

• A. VMs are not being migrated using vMotion.
• B. Snapshots cannot be created or consolidated.
• C. Hosts frequently disconnect from vCenter Server.
• D. VMs are not restarted after a host failure.

正解：D

解説：
vSphere HA is responsible for detecting host failures and restarting affected VMs on surviving hosts; if VMs aren't restarted after a host failure, it indicates an HA problem.

質問 # 52
An administrator is tasked with enabling Workload Management (vSphere Supervisor) on a VMware Cloud Foundation (VCF) workload domain using the SDDC Manager UI.
Which three are prerequisites for enabling Workload Management? (Choose three.)

• A. Verify that the vSphere Distributed Switch is configured with sufficient port groups.
• B. Verity at least one NSX Edge cluster is deployed and available.
• C. Verify that the cluster is runningvSAN.
• D. Verity at least one Content Library is available.
• E. Verify all hosts within the selected Sphere clusters have the proper vSphere with Tanzu licensing to support Workload Management.

正解：A、B、E

解説：
Supervisor relies on dedicated port groups on the vSphere Distributed Switch for control plane and workload traffic.
vSphere with Tanzu requires appropriate licensing on all cluster hosts to enable Workload Management features.
Workload Management uses NSX Edge clusters (and the associated load balancer services) to provide Kubernetes API endpoint availability.

質問 # 53
An administrator is tasked with deploying a new VMware Cloud Foundation (VCF) instance. The management domain is designed to be created with three virtual distributed switches (VDS) configured as follows:
VDS1 - used for management and vMotion traffic
VDS2 - used for vSAN traffic
VDS3 - used for NSX Overlay traffic
What action would the administrator take to deploy the designed configuration?

• A. vSphere Distributed Switch Profile 2 must be selected in the VCF Deployment parameter workbook.
• B. The design must be changed to ensure vSAN and NSX overlay traffic are on the same VDS.
• C. A JSON file must be prepared with the defined configuration and used to run the bring-up process.
• D. The ESXi hosts have to be configured with twelve physical NICs to ensure redundancy.

正解：C

質問 # 54
An administrator is preparing to deploy VMware Aria Suite Lifecycle using SDDC Manager.
Which three are prerequisites for deploying Aria Suite Lifecycle? (Choose three.)

• A. Ensure that the Application Virtual Networks have been configured.
• B. Ensure the VMware Software Install Bundle for VMware Aria Suite Lifecycle is in the local bundle repository.
• C. Ensure that a custom SSL certificate specifying the FQDN of the appliance is available.
• D. Verify that the password for the admin(g>local user account meets the complexity requirements.
• E. Ensure that the NTP and DNS settings specified in SDDC Manager are valid for all management components.

正解：B、C、E

解説：
Ensure that a custom SSL certificate specifying the FQDN of the appliance is available: A custom SSL certificate for the FQDN of the Aria Suite Lifecycle appliance is required for secure communication between components.
Ensure that the NTP and DNS settings specified in SDDC Manager are valid for all management components: Accurate NTP and DNS settings are crucial for time synchronization and proper domain resolution in the environment.
Ensure the VMware Software Install Bundle for VMware Aria Suite Lifecycle is in the local bundle repository: The required software bundle must be available in the local repository to ensure successful deployment.

質問 # 55
An administrator needs to delete and re-deploy an NSX Edge cluster that was originally deployed from SDDC Manager and has downloaded the edge cleaner tool.
Where should the administrator run the tool to complete this task?

• A. On the NSX Manager VM.
• B. On the Cloud Builder VM.
• C. On the Edge cluster node VM(s).
• D. On the SDDC Manager VM.

正解：C

解説：
The NSX Edge Cleaner tool is typically run on the Edge cluster node VM(s) to clean up the previous configuration and ensure that the node(s) are properly removed before re-deploying the NSX Edge cluster.
This process helps to reset the environment and remove any leftover configurations that may affect the re- deployment.

質問 # 56
Which feature of VMware Data Services Manager enhances security and compliance?

• A. Database level authentication
• B. Automated workload migration
• C. Network traffic encryption
• D. Storage replication

正解：A

解説：
VMware Data Services Manager™ offers modern database and data services management for vSphere. It is a solution that provides a data-as-a-service toolkit for on-demand provisioning and automated management of PostgreSQL and MySQL databases in vSphere environment.https://techdocs.broadcom.com/us/en/vmware-cis
/dsm/data-services-manager/2-1/about-vmware-data-services-manager.html

質問 # 57
An administrator needs to configure Network IO Control (NIOC) on a Virtual Distributed Switch (VDS) to prioritize storage traffic over other types of traffic.
Which two steps should be followed? (Choose two.)

• A. Create a new port group specifically for storage traffic.
• B. Migrate all VM traffic to a standard switch.
• C. Assign shares and limits to the new port group to prioritize the storage traffic.
• D. Navigate to the VDS settings in the vSphere Client and enable NIOC.
• E. Disable all other traffic types to ensure storage traffic gets full bandwidth.

正解：C、D

解説：
Network IO Control (NIOC) must be enabled on the Virtual Distributed Switch (VDS) via the vSphere Client to begin configuring and managing bandwidth allocation and prioritization for different types of traffic.
After enabling NIOC, you can assign shares and limits to the specific port group (in this case, for storage traffic) to prioritize the traffic over other types of network traffic.

質問 # 58
An administrator has deployed a new VI Workload Domain and must deploy a Kubernetes cluster on the vSphere Supervisor.
Which three steps should be followed to successfully deploy the Kubernetes cluster? (Choose three.)

• A. Configure a vSphere Namespace and assign resource quotas.
• B. Create a new VM template for the Kubernetes nodes.
• C. Enable Workload Management on the vSphere Cluster within SDDC Manager.
• D. Deploy an NSX Edge Cluster.
• E. Deploy a vSphere Pod Service.

正解：A、C、D

解説：
Comprehensive and Detailed Explanation From Exact Extract:
According to the VMware Cloud Foundation 5.2 Administration Guide and the VMware vSphere with Tanzu Documentation, the deployment of a Kubernetes cluster on a vSphere Supervisor requires the following key steps:
A . Configure a vSphere Namespace and assign resource quotas.
Exact Extract:
"After enabling workload management, you must create vSphere Namespaces to segment resources for Kubernetes workloads. Assigning resource quotas is required to control resource consumption within each namespace." (VMware vSphere with Tanzu Documentation - vSphere Namespaces) D . Deploy an NSX Edge Cluster.
Exact Extract:
"An NSX Edge Cluster is required for Kubernetes networking and load balancing capabilities within the Supervisor Cluster." (VMware Cloud Foundation Administration Guide - Preparing for Workload Management) E . Enable Workload Management on the vSphere Cluster within SDDC Manager.
Exact Extract:
"To use vSphere Supervisor and deploy Kubernetes clusters, enable Workload Management on the appropriate vSphere Cluster from within SDDC Manager." (VMware Cloud Foundation Administration Guide - Enabling Workload Management) Why Not the Other Options?
B: Deploying a vSphere Pod Service is optional and not a required step for deploying a standard Kubernetes cluster on Supervisor.
C: Creating a new VM template for Kubernetes nodes is not required; the Supervisor Cluster automatically manages the deployment and configuration of Kubernetes control plane and worker nodes.
Summary:
To successfully deploy a Kubernetes cluster on the vSphere Supervisor in a new VI Workload Domain, the administrator must:
Enable Workload Management (E),
Deploy an NSX Edge Cluster (D), and
Configure a vSphere Namespace with resource quotas (A).
These steps are specified in the official VMware documentation.

質問 # 59
An administrator is tasked with enabling Workload Management (vSphere IaaS control plane) on a VMware Cloud Foundation workload domain.
Which three of the following are prerequisites for enabling Workload Management? (Choose three.)

• A. Install the vSphere Client on all ESXi hosts.
• B. Ensure that the cluster has at least three ESXi hosts.
• C. Configure NTP and DNS settings for all management components.
• D. Verify that all ESXi hosts are running vSphere 7.0 or later.

正解：B、C、D

解説：
For Workload Management in VMware Cloud Foundation, a minimum of three ESXi hosts is required to create a robust, highly available vSphere cluster.
Proper NTP and DNS configuration is essential to ensure time synchronization and proper resolution of network names, which are critical for Workload Management.
The hosts must be running vSphere 7.0 or later to be compatible with the latest features and requirements for Workload Management.

質問 # 60
During the deployment of a VI workload domain using SDDC Manager, an administrator encounters issues with host configuration.
Which three steps should be followed to troubleshoot and resolve the configuration issues? (Choose three.)

• A. Verify that all ESXi hosts are connected to the management network.
• B. Check the compatibility of the hardware with VMware Cloud Foundation requirements.
• C. Restart the SDDC Manager appliance to reset configurations.
• D. Reconfigure the NSX Edge nodes.
• E. Ensure that all ESXi hosts have the correct version of ESXi installed.

正解：A、B、E

質問 # 61
An administrator can set resource limits and container defaults on a vSphere Namespace.
Which three resource limits can be set? (Choose three.)

• A. Number of containersF Network
• B. CPU
• C. StorageB Memory

正解：A、B、C

解説：
vSphere Namespaces allow defining resource limits for Memory and CPU, as well as Storage capacity, which govern the allocation available to workloads within the namespace.
https://techdocs.broadcom.com/us/en/vmware-cis/vsphere/vsphere-supervisor/8-0/vsphere-supervisor- services-and-workloads-8-0/configuring-and-managing-vsphere-namespaces/set-resource-limits-to-a-vsphere- namespace.html

質問 # 62
Which two steps should an administrator perform to configure the backup of the VMware Cloud Foundation (VCF) SDDC Manager and NSX components to allow them to be recovered in the event of a full site failure?
(Choose two.)

• A. Prepare an external SFTP server to store file-based backups.
• B. Define a scheduled task in vCenter to create a snapshot of the NSX Edge cluster.
• C. Configure image-based backup for the NSX Manager cluster.
• D. Configure the backup settings in SDDC Manager.
• E. Backup the NSX Manager configuration by exporting it to an archive file.

正解：A、D

解説：
According to the officialVMware Cloud Foundation 5.2 Administration GuideandVMware NSX Data Center documentation, the required and recommended steps to enable proper backup and recovery for the SDDC Manager and NSX Manager components are as follows:
Option B: Configure the backup settings in SDDC Manager.Exact Extract from official documentation:
"You must configure backup settings in SDDC Manager to ensure scheduled, automated backups of critical SDDC Manager configuration and inventory data. Backups are stored as files that can be used to restore SDDC Manager in case of a failure or disaster." (VMware Cloud Foundation Administration Guide - Backing Up SDDC Manager) Option D: Prepare an external SFTP server to store file-based backups.Exact Extract from official documentation:
"Configure an external SFTP server to store SDDC Manager backup files. SDDC Manager supports only file- based backups using SFTP as the storage protocol." (VMware Cloud Foundation Administration Guide - Configuring Backup Destinations) Why Not the Other Options?
Option A:Exporting an archive file from NSX Manager is a manual method and does not constitute a complete, restorable backup suitable for full site failure recovery.
Option C:Image-based backups for NSX Manager arenot supportedand can cause issues with the integrity and recoverability of NSX appliances, as per VMware best practices.
Option E:Snapshots of the NSX Edge cluster arenot supportedfor backup and recovery; VMware specifically advises against using snapshots for backup purposes of NSX appliances.
Summary:
The administrator mustconfigure the backup settings in SDDC Manager (B)andprepare an external SFTP server (D)to enable secure, automated, and restorable backups of SDDC Manager and NSX components, as recommended and required by the official VMware Cloud Foundation 5.2 documentation.

質問 # 63
An administrator recently incorrectly deployed a new isolated VI workload domain within an existing VMware Cloud Foundation (VCF) instance.
How can the administrator reconfigure the VI workload domain to share the SSO domain from the management workload domain?

• A. From the management domain vCenter Server instance, use the rsautil command to add the VI workload domain to the management domain.
• B. From the SDDC Manager console, migrate the VI workload domain to the management domain.
• C. A new VI workload domain must be created through SDDC Manager.
• D. From the VI workload domain vCenter Server instance, add the management domain SSO and remove the isolated SSO.

正解：C

解説：
According to VMware Cloud Foundation documentation, once a VI workload domain has been deployed as an isolated domain (with its own SSO), it cannot be reconfigured after deployment to join the management domain's SSO domain. The official guidance states that the only supported approach is to delete the incorrectly configured VI workload domain and create a new one through SDDC Manager, ensuring it is properly configured to share the SSO domain with the management domain during the deployment process.
There is no supported process to convert or migrate an existing isolated SSO VI workload domain to a shared SSO configuration after deployment.

質問 # 64
An organization needs to perform maintenance on a specific host in a vSAN cluster. An administrator is required to put the host into maintenance mode whilst ensuring that all VMs in the cluster remain accessible.
Which three steps should the administrator take to correctly set a vSAN host into maintenance mode? (Choose three.)

• A. Migrate all VMs manually from the host before enabling maintenance mode.
• B. Select the "No Data Migration" option to speed up the process.
• C. Navigate to the vSAN cluster in the vSphere Client and select the host.
• D. Choose the "Ensure Accessibility" option to maintain data accessibility.
• E. Right-click the host and select "Enter Maintenance Mode."

正解：C、D、E

解説：
The "Ensure Accessibility" option ensures that all data remains accessible during maintenance while minimizing the impact on performance and data migration.
The administrator must navigate to the vSAN cluster in the vSphere Client to select the host for maintenance mode.
Right-clicking the host and selecting "Enter Maintenance Mode" is the standard action for placing a host into maintenance mode.

質問 # 65
Which VMware vSphere feature provides the ability to define and apply datastore capabilities to ensure virtual machines meet specific performance and availability requirements?

• A. Host Profiles
• B. Storage Policy Components
• C. Storage Policies
• D. Performance Service

正解：C

解説：
Storage Policies in VMware vSphere allow administrators to define and apply specific storage requirements for virtual machines, ensuring they meet desired performance and availability standards. These policies enable the alignment of VM storage needs with the capabilities of the underlying datastores.

質問 # 66
A disk failure has occurred in a vSAN cluster.
What four steps should be taken to recover from this disk failure? (Choose four.)

• A. Disable disk group encryption
• B. Rebuild the affected disk group
• C. Use the vSohere Client to check the vSAN Health Service
• D. Replace the failed disk with a new one
• E. Ensure the new disk is claimed by the vSAN cluster
• F. Perform a full resync of the vSAN objects

正解：B、C、D、E

解説：
Checking the vSAN Health Service in the vSphere Client is the first step in diagnosing the issue and verifying the status of the vSAN components after the disk failure.
Rebuilding the affected disk group is necessary to ensure that data is re-optimized and replicated in accordance with the vSAN policy.
Replacing the failed disk with a new one ensures that the storage capacity is restored.
Ensuring that the new disk is claimed by the vSAN cluster is important to ensure that it is recognized and integrated into the vSAN disk group.

質問 # 67
What is the impact of consolidating snapshots on a virtual machine?

• A. It changes the VM's hardware compatibility settings.
• B. It reverts the VM to the state of the first snapshot taken.
• C. It temporarily increases the available disk space consumption on the datastore while merging data.
• D. It disconnects the VM from the network temporarily.

正解：C

解説：
When consolidating snapshots, the data from the snapshot files is merged back into the original virtual disk. This process temporarily increases the disk space usage on the datastore because of the additional space required to merge the snapshot data into the primary disk.

質問 # 68
An administrator's passwords for their NSX 'root', 'admin', and 'audit' accounts in the Cloud Foundation management domain expired. The administrator logged into the NSX Manager console and changed the passwords for all three accounts. The passwords are now showing a status of "Disconnected" in the SDDC Manager UI.

• A. In order to correct this issue, how can SDDC Manager be updated with the new passwords?
• B. In SDDC Manager, navigate to Password Management and select the account with the password with a "Disconnected" status, click the vertical ellipsis (three dots), and click Sync.
• C. In SDDC Manager, navigate to Password Management and select the account with the password with a "Disconnected" status, click the vertical ellipsis (three dots), and click Rotate.
• D. In SDDC Manager, navigate to Password Management and select the account with the password with a "Disconnected" status, click the vertical ellipsis (three dots), and click Remediate.

正解：C

解説：
To resolve the issue of disconnected accounts in SDDC Manager after password changes, the administrator must navigate to the Password Management section in the SDDC Manager UI. From there, the administrator can select the affected account, click the vertical ellipsis (three dots), and choose Update to enter the new password for that account, ensuring SDDC Manager is synced with the correct credentials.

質問 # 69
......

2025年最新の有効な2V0-11.25テスト解答VMware試験PDF：https://www.passtest.jp/VMware/2V0-11.25-shiken.html

無料VMware 2V0-11.25試験問題と解答トレーニングにはPassTest：https://drive.google.com/open?id=1WxiDFPWvdQarQgkB-7TZAxsjVIOtb39g