PDFを無料でダウンロードにはJN0-351有効な練習テスト問題があります
JN0-351テストエンジンお試しセット、JN0-351問題集PDF
質問 # 30
You deployed a new EX Series switch with DHCP snooping enabled and you do not see any entries in the snooping databases for an interface. Which two Juniper configurations for that interface caused this issue?
(Choose two.)
- A. The interface is configured as a disabled port.
- B. The interface is configured as a trunk port.
- C. Dynamic ARP inspection is enabled on the interface.
- D. MAC limiting is enabled on the interface.
正解：A、B
解説：
A is correct because the interface is configured as a disabled port. A disabled port does not forward any traffic, including DHCP packets. Therefore, DHCP snooping cannot learn any MAC addresses or lease information from a disabled port1.
C is correct because the interface is configured as a trunk port. By default, all trunk ports on the switch are trusted for DHCP snooping2. This means that DHCP snooping does not inspect or filter any DHCP packets received on a trunk port. Therefore, DHCP snooping does not add any entries to the snooping database for a trunk port2.
質問 # 31
You are asked to create a new firewall filter to evaluate Layer 3 traffic that is being sent between VLANs. In this scenario, which two statements are correct? (Choose two.)
- A. You should apply the firewall filter to the appropriate VLAN.
- B. You should apply the firewall filter to the appropriate IRB interface.
- C. You should create a family Ethernet-switching firewall filter with the appropriate match criteria and actions.
- D. You should create a family inet firewall filter with the appropriate match criteria and actions.
正解：B、D
解説：
Explanation
A firewall filter is a configuration that defines the rules that determine whether to forward or discard packets at specific processing points in the packet flow. A firewall filter can also modify the attributes of the packets, such as priority, marking, or logging. A firewall filter can be applied to various interfaces, protocols, or routing instances on a Juniper device1.
A firewall filter has a family attribute, which specifies the type of traffic that the filter can evaluate. The family attribute can be one of the following: inet, inet6, mpls, vpls, iso, or ethernet-switching2. The family inet firewall filter is used to evaluate IPv4 traffic, which is the most common type of Layer 3 traffic on a network.
To create a family inet firewall filter, you need to specify the appropriate match criteria and actions for each term in the filter. The match criteria can include various fields in the IPv4 header, such as source address, destination address, protocol, port number, or DSCP value. The actions can include accept, discard, reject, count, log, policer, or next term3.
To apply a firewall filter to Layer 3 traffic that is being sent between VLANs, you need to apply the filter to the appropriate IRB interface. An IRB interface is an integrated routing and bridging interface that provides Layer 3 functionality for a VLAN on a Juniper device. An IRB interface has an IP address that acts as the default gateway for the hosts in the VLAN. An IRB interface can also participate in routing protocols and forward packets to other VLANs or networks4.
Therefore, option C is correct, because you should create a family inet firewall filter with the appropriate match criteria and actions. Option D is correct, because you should apply the firewall filter to the appropriate IRB interface.
Option A is incorrect, because you should not create a family ethernet-switching firewall filter with the appropriate match criteria and actions. A family ethernet-switching firewall filter is used to evaluate Layer 2 traffic on a Juniper device. A family ethernet-switching firewall filter can only match on MAC addresses or VLAN IDs, not on IP addresses or protocols5.
Option B is incorrect, because you should not apply the firewall filter to the appropriate VLAN. A VLAN is a logical grouping of hosts that share the same broadcast domain on a Layer 2 network. A VLAN does not have an IP address or routing capability. A firewall filter cannot be applied directly to a VLAN; it must be applied to an interface that belongs to or connects to the VLAN6.
References:
1: Firewall Filters Overview 2: Configuring Firewall Filters 3: Configuring Firewall Filter Match Conditions and Actions 4: Understanding Integrated Routing and Bridging Interfaces 5: Configuring Ethernet-Switching Firewall Filters 6: Understanding VLANs
質問 # 32
Exhibit
What does the * indicate in the output shown in the exhibit?
- A. The interface is down.
- B. The switch ports have a router attached.
- C. The interface is active.
- D. All interfaces have elected a root bridge.
正解：C
解説：
The exhibit shows the output of the command show vlans brief, which displays brief information about VLANs and their associated interfaces1.
The output has four columns: Routing instance, VLAN name, Interfaces, and Tagging.
The * symbol indicates that the interface is active, meaning that it is up and forwarding traffic1. This can be verified by the command , which displays the status of the interfaces2.
質問 # 33
Which two types of tunnels are able to be created on all Junos devices? (Choose two.)
- A. IPsec
- B. GRE
- C. IP-IP
- D. STP
正解：A、B
解説：
Explanation
Junos devices support various types of tunnels for different purposes12.
Option B is correct. Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol network1. Junos devices support GRE tunnels1.
Option D is correct. IPsec (Internet Protocol Security) is a protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session1. Junos devices support IPsec tunnels1.
Option A is incorrect. Spanning Tree Protocol (STP) is not a type of tunnel. It's a network protocol designed to prevent loops in a bridged Ethernet local area network2.
Option C is incorrect. While Junos devices do support IP-IP (also known as IP tunneling), it's not supported on all Junos devices1.
質問 # 34
Which statement is correct about graceful Routing Engine switchover (GRES)?
- A. The PFE restarts and the kernel and interface information is lost.
- B. When combined with NSR, routing is preserved and the new master RE does not restart rpd.
- C. With no other high availability features enabled, routing is preserved and the new master RE does not restart rpd.
- D. GRES has a helper mode and a restarting mode.
正解：B
解説：
Explanation
The Graceful Routing Engine Switchover (GRES) feature in Junos OS enables a router with redundant Routing Engines to continue forwarding packets, even if one Routing Engine fails1. GRES preserves interface and kernel information, ensuring that traffic is not interrupted1. However, GRES does not preserve the control plane1.
To preserve routing during a switchover, GRES must be combined with either Graceful Restart protocol extensions or Nonstop Active Routing (NSR)1. When GRES is combined with NSR, nearly 75 percent of line rate worth of traffic per Packet Forwarding Engine remains uninterrupted during GRES1. Any updates to the primary Routing Engine are replicated to the backup Routing Engine as soon as they occur1.
Therefore, when GRES is combined with NSR, routing is preserved and the new master RE does not restart rpd1.
質問 # 35
Which two BGP attributes must be supported by all BGP implementations and must be included in every update? (Choose two.)
- A. MED
- B. community
- C. next hop
- D. AS path
正解：C、D
解説：
Explanation
BGP attributes are properties that BGP uses for route advertisement, path selection, and loop prevention1. There are four categories of BGP attributes123:
Well-known mandatory: Must be recognized by all BGP routers, present in all BGP updates, and passed on to other BGP routers123.
Well-known discretionary: Supported by all BGP implementations, and are optionally included in BGP updates1.
Optional transitive: May not be supported by all implementations of BGP1.
Optional non-transitive: May not be supported by all implementations of BGP1.
The well-known mandatory attributes must be supported by all BGP implementations and must be included in every update123. These include the AS path and next hop attributes23. Therefore, options A and C are correct.
質問 # 36
You are attempting to configure the initial two aggregated Ethernet interfaces on a router but there are no aggregated Ethernet interfaces available.
In this scenario, which configuration will enable these interfaces on this router?
- A.
- B.
- C.
- D.
正解：A
解説：
Explanation
The correct answer to your question is
Option C shows the configuration of the statement, which defines the properties of the router chassis, such as the number of aggregated Ethernet interfaces, the number of FPCs, and the number of PICs1.
To enable aggregated Ethernet interfaces on a router, you need to specify the aggregated-devices statement under the chassis parameter to the desired number of interfaces2. For example, to enable two aggregated Ethernet interfaces, you can use the following configuration:
chassis { aggregated-devices { ethernet { device-count 2; } } }
Option C shows this configuration with the device-count set to 2, which will enable two aggregated Ethernet interfaces on the router. The other options do not show this configuration and will not enable any aggregated Ethernet interfaces on the router.
Therefore, option C is the correct answer to your question.
質問 # 37
Exhibit.
Why is this OSPF adjacency remaining in this state?
- A. A hello interval mismatch exists between the OSPF neighbors.
- B. An area ID mismatch exists between the OSPF neighbors
- C. A subnet mask mismatch exists between the OSPF neighbors.
- D. An MTU mismatch exists between the OSPF neighbors.
正解：D
解説：
The exhibit shows the output of the command , which displays information about the OSPF neighbors on a router1.
The output shows that the OSPF neighbor with the address 172.26.1.1 and the interface ge-0/0/3.0 is in the Exstart state1.
The Exstart state is the fourth state in the OSPF neighbor formation process, after Down, Init, and
2-Way states2. In this state, the OSPF neighbors establish a master-slave relationship and exchange database description (DBD) packets, which contain summaries of their link-state databases2.
The most common reason for OSPF neighbors to be stuck in the Exstart state is an MTU mismatch between the interfaces3. MTU stands for maximum transmission unit, which is the largest size of a packet that can be transmitted on a network segment4. If the MTU values of two OSPF neighbors are different, theymay not be able to exchange DBD packets successfully, as some packets may be dropped or fragmented due to their size exceeding the MTU limit3.
To solve this problem, you need to ensure that the MTU values of both OSPF neighbors are the same or compatible. You can use the command show interfaces to display the MTU value of an interface5. You can also use the command ping with the do-not-fragment option to test the MTU size between two routers. You can change the MTU value of an interface by using the command set interfaces interface-name mtu mtu-value in configuration mode5.
質問 # 38
Exhibit
Referring to the exhibit, which two configuration changes must you apply for packets to reach from R1 to R3 using IS-IS? (Choose two.)
- A. On R1, disable Level 2 on the ge-0/0/1 interface.
- B. On R3 enable Level 1 on the ge-0/0/4 interface
- C. On R1, enable Level 1 on the ge-0/0/1 interface.
- D. On R3 disable Level 2 on the ge-0/0/4 interface.
正解：B、C
解説：
Explanation
A: On R1, enable Level 1 on the ge-0/0/1 interface. In IS-IS, both levels (Level 1 and Level 2) are enabled by default when you enable IS-IS on an interface1. Level 1 systems route within an area2. If the destination is outside an area, Level 1 systems route toward a Level 2 system2. Therefore, enabling Level 1 on the ge-0/0/1 interface on R1 would allow packets to reach from R1 to R3.
D: On R3 enable Level 1 on the ge-0/0/4 interface Similarly, enabling Level 1 on the ge-0/0/4 interface on R3 would allow packets to reach from R1 to R3.
These explanations are based on the IS-IS configuration documents and learning resources available at Juniper Networks1 and Cisco34.
質問 # 39
Exhibit.
You have configured the four EX Series switches with RSTP, as shown in the exhibit. You discover that whenever a link between switches goes up or down, the switches take longer than expected for RSTP to converge, using the default settings.
In this scenario, which action would solve the delay in RSTP convergence?
- A. The bridge priority for EX-4 must be set at 4000.
- B. The force-version must be removed.
- C. The hello-time must be increased.
- D. The max-age must be increased to 20
正解：B
解説：
The exhibit shows the configuration of RSTP on EX-4, which has the command force-version stp. This command forces the switch to use the legacy STP protocol instead of RSTP, even though the switch supports RSTP1. This means that EX-4 will not be able to take advantage of the faster convergence and enhanced features of RSTP, such as edge ports, link type, and proposal/agreement sequence2.
The other switches in the network are likely to be running RSTP, as it is the default protocol for EX Series switches3. Therefore, there will be a compatibility issue between EX-4 and the other switches, which will result in longer convergence times and suboptimal performance. The switch will also generate a warning message that says "Warning: STP version mismatch with neighbor" when it receives a BPDU from a RSTP neighbor1.
To solve this problem, the force-version command must be removed from EX-4, so that it can run RSTP natively and interoperate with the other switches in the network. This will enable faster convergence and better stability for the network topology. To remove the command, you can use the delete protocols rstp force-version command in configuration mode1.
質問 # 40
You want to ensure traffic is routed through a GRE tunnel.
In this scenario, which two statements will satisfy this requirement? (Choose two.)
- A. All intermediary devices must have a route to the tunnel endpoints.
- B. Tunnel endpoints must have a route that directs traffic into the tunnel.
- C. Keepalives must be used on stateless tunneling protocols.
- D. BFD must be used on the stateless tunneling protocols.
正解：A、B
解説：
Explanation
Option A is correct. For traffic to be sent through a GRE tunnel, there must be a route that directs the traffic into the tunnel. This is typically accomplished through the use of a static route or a dynamic routing protocol.
Option B is correct. All intermediary devices must have a route to the tunnel endpoints34. In real-world scenarios, the tunnel endpoints for a tunnel going over the Internet must have globally reachable internet addresses. Otherwise, intermediate routers in the Internet cannot forward the tunneled packets.
質問 # 41
Which two statements are correct about tunnels? (Choose two.)
- A. IP-IP tunnels are stateful.
- B. BFD cannot be used to monitor tunnels.
- C. Tunnel endpoints must have a valid route to the remote tunnel endpoint.
- D. Tunnels add additional overhead to packet size.
正解：C、D
解説：
Explanation
A tunnel is a connection between two computer networks, in which data is sent from one network to another through an encrypted link. Tunnels are commonly used to secure data communications between two networks or to connect two networks that use different protocols.
Option B is correct, because tunnel endpoints must have a valid route to the remote tunnel endpoint. A tunnel endpoint is the device that initiates or terminates a tunnel connection. For a tunnel to be established, both endpoints must be able to reach each other over the underlying network. This means that they must have a valid route to the IP address of the remote endpoint1.
Option D is correct, because tunnels add additional overhead to packet size. Tunnels work by encapsulating packets: wrapping packets inside of other packets. This means that the original packet becomes the payload of the surrounding packet, and the surrounding packet has its own header and trailer. The header and trailer of the surrounding packet add extra bytes to the packet size, which is called overhead. Overhead can reduce the efficiency and performance of a network, as it consumes more bandwidth and processing power2.
Option A is incorrect, because BFD can be used to monitor tunnels. BFD is a protocol that can be used to quickly detect failures in the forwarding path between two adjacent routers or switches. BFD can be integrated with various routing protocols and link aggregation protocols to provide faster convergence and fault recovery.
BFD can also be used to monitor the connectivity of tunnels, such as GRE, IPsec, or MPLS.
Option C is incorrect, because IP-IP tunnels are stateless. IP-IP tunnels are a type of tunnels that use IP as both the encapsulating and encapsulated protocol. IP-IP tunnels are simple and easy to configure, but they do not provide any security or authentication features. IP-IP tunnels are stateless, which means that they do not keep track of the state or status of the tunnel connection. Stateless tunnels do not require any signaling or negotiation between the endpoints, but they also do not provide any error detection or recovery mechanisms.
References:
1: What is Tunneling? | Tunneling in Networking 2: What Is Tunnel In Networking, Its Types, And Its Benefits? : [Configuring Bidirectional Forwarding Detection] : [IP-IP Tunneling]
質問 # 42
A new network requires multiple topology support. You decide to use IS-IS in this situation. Which three protocol topologies are supported in this scenario? (Choose three.)
- A. multicast
- B. IPsec
- C. IPv4
- D. IPv6
- E. anycast
正解：A、C、D
解説：
Explanation
IS-IS (Intermediate System to Intermediate System) is a routing protocol that is designed to move information efficiently within a computer network12. It supports multiple protocol topologies, including IPv4, IPv6, and multicast12. Therefore, options C, E, and D are correct.
質問 # 43
Which statement about aggregate routes is correct?
- A. Aggregate routes are used for advertising summarized network prefixes.
- B. Aggregate routes are always preferred over more specific routes, even when the specific routes have a better path.
- C. Aggregate routes can only be used for static routing but not for dynamic routing protocols.
- D. Aggregate routes are automatically generated for all of the subnets in a routing table.
正解：A
解説：
Explanation
Aggregate routes are used for advertising summarized network prefixes12. They help minimize the number of routing tables in an IP network by consolidating selected multiple routes into a single route advertisement1. This approach is in contrast to non-aggregation routing, in which every routing table contains a unique entry for each route1.
Therefore, option D is correct. Options A, B, and C are not correct because:
Aggregate routes can be used with both static routing and dynamic routing protocols1.
Aggregate routes are not automatically generated for all of the subnets in a routing table. They need to be manually configured1.
Aggregate routes are not always preferred over more specific routes. The route selection process in Junos OS considers several factors, including route preference and metric, before determining the active route1.
質問 # 44
You have two OSPF routers forming an adjacency. R1 has a priority of 32 and a router ID of 192.168.1.2. R2 has a priority of 64 and a router ID of 192.168.1.1. The routers were started at the same time and all other OSPF settings are the default settings.
Which statement is correct in this scenario?
- A. Router IDs must match for an adjacency to form.
- B. At least three routers are required for a DR/BDR election
- C. R2 will be the BDR.
- D. R1 will be the BDR.
正解：D
解説：
Explanation
In OSPF, the Designated Router (DR) and Backup Designated Router (BDR) are elected based on the priority of the routers1. The router with the highest priority becomes the DR, and the router with the second highest priority becomes the BDR1. If there is a tie in priority, then the router with the highest Router ID is chosen1.
In this scenario, R2 has a higher priority (64) than R1 (32), so R2 will become the DR1. Since R1 has the second highest priority, it will become the BDR1. Therefore, option D is correct.
質問 # 45
Exhibit.
You want to enable redundancy for the EBGP peering between the two routers shown in the exhibit. Which three actions will you perform in this scenario? (Choose three.)
- A. Configure loopback interface peering.
- B. Configure routes for the peer loopback interface IP addresses.
- C. Configure a cluster ID.
- D. Configure an MD5 peer authentication.
- E. Configure BGP multihop.
正解：A、B、E
解説：
A is correct because you need to configure BGP multihop to enable redundancy for the EBGP peering between the two routers. BGP multihop is a feature that allows BGP peers to establish a session over multiple hops, instead of requiring them to be directly connected1. By default, EBGP peers use a time-to-live (TTL) value of 1 for their packets, which means that they can only reach adjacent neighbors1. However, if you configure BGP multihop with a higher TTL value, you can allow EBGP peers to communicate over multiple routers in between1. This can provide redundancy in case of a link failure or a router failure between the EBGP peers.
B is correct because you need to configure loopback interface peering to enable redundancy for the EBGP peering between the two routers. Loopback interface peering is a technique that uses loopback interfaces as the source and destination addresses for BGP sessions, instead of physical interfaces2. Loopback interfaces are virtual interfaces that are always up andreachable as long as the router is operational2. By using loopback interface peering, you can avoid the dependency on a single physical interface or link for the BGP session, and use multiple paths to reach the loopback address of the peer2. This can provide redundancy and load balancing for the EBGP peering.
C is correct because you need to configure routes for the peer loopback interface IP addresses to enable redundancy for the EBGP peering between the two routers. Routes for the peer loopback interface IP addresses are necessary to ensure that the routers can reach each other's loopback addresses over multiple hops2. You can use static routes or dynamic routing protocols to advertise and learn the routes for the peer loopback interface IP addresses2. Without these routes, the routers will not be able to establish or maintain the BGP session using their loopback interfaces.
質問 # 46
Which statement is correct about IP-IP tunnels?
- A. There are 24 bytes of overhead with IP-IP encapsulation.
- B. The TTL in the inner packet is decremented during transit to the tunnel endpoint.
- C. IP-IP tunnels only support encapsulating IP traffic.
- D. IP-IP tunnels only support encapsulating non-IP traffic.
正解：C
解説：
Explanation
IP-IP tunnels are a type of tunnels that use IP as both the encapsulating and encapsulated protocol. IP-IP tunnels are simple and easy to configure, but they do not provide any security or authentication features. IP-IP tunnels only support encapsulating IP traffic, which means that the payload of the inner packet must be an IP packet. IP-IP tunnels cannot encapsulate non-IP traffic, such as Ethernet frames or MPLS labels1.
Option A is correct, because IP-IP tunnels only support encapsulating IP traffic. Option B is incorrect, because IP-IP tunnels only support encapsulating non-IP traffic. Option C is incorrect, because the TTL in the inner packet is not decremented during transit to the tunnel endpoint. The TTL in the outer packet is decremented by each router along the path, but the TTL in the inner packet is preserved until it reaches the tunnel endpoint2.
Option D is incorrect, because there are 20 bytes of overhead with IP-IP encapsulation. The overhead consists of the header of the outer packet, which has a fixed size of 20 bytes for IPv43.
References:
1: IP-IP Tunneling 2: What is tunneling? | Tunneling in networking 3: IPv4 - Header
質問 # 47
An update to your organization's network security requirements document requires management traffic to be isolated in a non-default routing-instance. You want to implement this requirement on your Junos-based devices.
Which two commands enable this behavior? (Choose two.)
- A. set routing-instances mgmt_junos
- B. set routing-instances mgmtjunoa interface ge-0/0/0.0
- C. set routing-instances mgmt_junos interface em1
- D. set system management-instance
正解：A、D
解説：
Explanation
To isolate management traffic in a non-default routing-instance on Junos-based devices, you can use the set system management-instance and set routing-instances mgmt_junos commands12.
set system management-instance: This command associates the management interface (usually named fxp0 or em0 for Junos OS, or re0:mgmt-* or re1:mgmt-* for Junos OS Evolved) with the non-default virtual routing and forwarding (VRF) instance1. After you configure the non-default management VRF instance, management traffic no longer has to share a routing table with other control traffic or protocol traffic1.
set routing-instances mgmt_junos: This command creates a new routing instance named mgmt_junos. The name of the dedicated management VRF instance is reserved and hardcoded as mgmt_junos; you cannot configure any other routing instance by the name mgmt_junos1.
Therefore, options C and D are correct. Options A and B are not correct because they attempt to assign an interface to the mgmt_junos routing instance, which is not necessary for isolating management traffic1.
質問 # 48
What are two reasons for creating multiple areas in OSPF? (Choose two.)
- A. to reduce the convergence time
- B. to increase the size of the LSDB
- C. to reduce LSA flooding across the network
- D. to increase the number of adjacencies in the backbone
正解：A、C
解説：
Explanation
Option A is correct. Creating multiple areas in OSPF can help to reduce the convergence time . This is because changes in one area do not affect other areas, so fewer routers need to run the SPF algorithm in response to a change.
Option D is correct. Creating multiple areas in OSPF can help to reduce Link State Advertisement (LSA) flooding across the network. This is because LSAs are not flooded out of their area of origin.
質問 # 49
After receiving a BGP route, which two conditions are verified by the receiving router to ensure that the received route is valid? (Choose two)
- A. The next hop is reachable.
- B. The AS-path length is greater than 0.
- C. The loops do not exist.
- D. The local preference is greater than 0.
正解：A、C
解説：
B is correct because the loops do not exist is one of the conditions that are verified by the receiving router to ensure that the received BGP route is valid. A loop in BGP means that a route has been advertised by the same AS more than once, which can cause routing instability and inefficiency1. To prevent loops, BGP uses the AS-path attribute, which lists the AS numbers that a route has traversed from the origin to the destination2. The receiving router checks the AS-path attribute of the received route and discards it if it finds its own AS number in the list2. This way, BGP avoids accepting routes that contain loops.
C is correct because the next hop is reachable is one of the conditions that are verified by the receiving router to ensure that the received BGP route is valid. The next hop is the IP address of the next router that is used to forward packets to the destination network3. The receiving router checks the next hop attribute of the received route and verifies that it has a valid route to reach it3. If the next hop is not reachable, the received route is not usable and is rejected by the receiving router3. This way, BGP ensures that only feasible routes are accepted.
質問 # 50
Two routers share the same highest priority and start time.
- A. The router with the highest router ID becomes the DR
- B. The router with the highest MAC address become the DR
- C. The routers perform another DR election.
- D. In this situation, what is evaluated next when determining the designated router? The router with the lowest router ID become the DR.
正解：A
解説：
According to the OSPF protocol, the designated router (DR) is the router that acts as the focal point for exchanging routing information on a multi-access network segment, such as a LAN1. The DR election process is based on the following criteria, in order of precedence1:
The router with the highest OSPF priority becomes the DR. The default priority is 1, and a priority of 0 means the router will not participate in the election.
If there is a tie in priority, the router with the highest router ID becomes the DR. The router ID is a 32-bit number that uniquely identifies a router in an OSPF domain. It can be manually configured or automatically derived from the highest IP address of a loopback interface or a physical interface.
If there is a tie in router ID, the router that was first to become an OSPF neighbor becomes the DR.
In your scenario, two routers share the same highest priority and start time. This means that they have equal chances of becoming the DR based on the first and third criteria. Therefore, the second criterion will be used to break the tie, which is the router ID. The router with the highest router ID will become the DR, and the other router will become the backup designated router (BDR), which is ready to take over the role of DR if it fails1.
質問 # 51
......
あなたを合格させるJNCIS-ENT JN0-351試験問題集で2023年12月15日には67問あります：https://www.passtest.jp/Juniper/JN0-351-shiken.html
最新のJuniper JN0-351のPDFと問題集で（2023）無料試験問題解答：https://drive.google.com/open?id=10biVf1BYxkLuCCT_2Sta51bVD9lJK17c