結果を保証するには最新2025年05月無料AMPP Senior-Internal-Corrosion-Technologistで練習しよう
有効な問題最新版を無料で試そうSenior-Internal-Corrosion-Technologist試験問題集解答
質問 # 14
You are the NACE Coating Inspector ona tank lining project where desiccant dehumidificationis being used.
Since the first shift ofabrasive Wasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Advise the coating applicator supervisor of your readings
- C. Document the readings at the end of the shift
- D. Check to see if the dehumidification equipment is operating correctly
正解：B
質問 # 15
Which product Is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. Coal Tar Enamel
- B. Concrete
- C. 2-Layer Polyethylene (PE)
- D. 3-Layer Polyethylene (PE)
正解：A
質問 # 16
When performing Inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A destructive paint inspection Tooke gauge
- B. A set of 14 pencils of varying hardness
- C. A mechanical adhesion tester
- D. A hardness tester
正解：A
質問 # 17
When observing design defects the NACE Inspector should:
- A. Request that the item be rebuilt with a better design for coating
- B. Stop the job immediately
- C. Ignore the defect as the inspector can't change the design
- D. Document the defect and the potential problems that could result
正解：D
質問 # 18
The Concrete Repair Institute's comparators can be used to assess:
- A. Contamination levels prior to coating
- B. Surface cleanliness prior to coating
- C. Surface profile prior to coating
- D. Compressive and tensile strength prior to coating
正解：B
質問 # 19
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Distribution
- B. Gathering
- C. Midstream
- D. Transmission
正解：C
質問 # 20
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. washed with dean potable water prior to use.
- B. disposed of properly.
- C. run through the air wash separator.
- D. mixed with uncontaminated abrasive
正解：A
質問 # 21
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Getstage
- D. Wetting stage
正解：B
質問 # 22
All of these ate advantages of using repair patches EXCEPT
- A. inert to common acids, alkalis, and solvents.
- B. barrier to moisture and corrosion.
- C. special tools or equipment are required.
- D. excellent abrasion resistance.
正解：C
質問 # 23
II Is always possible to see moisture on a steel substrate:
- A. False
- B. True
正解：A
質問 # 24
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. type of dehumidification equipment (refrigerant or desiccant).
- B. manufacturer of the equipment.
- C. coating type.
- D. time of the year (winter/summer).
正解：A
質問 # 25
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. coatings are expected to degrade over time.
- B. coatings are more durable than linings.
- C. linings protect the contents and the container.
- D. linings are more durable than coatings.
正解：C
質問 # 26
Coating application to concrete substrates is:
- A. Less challenging than coating steel
- B. More challenging than coating steel
- C. Not required as concrete is Inorganic
- D. The same as coating steel
正解：B
質問 # 27
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only those directly Involved in the project would understand
- B. Language that the most people would understand
- C. Language that only technical experts would understand
- D. Language that another NACE Inspector would understand
正解：B
質問 # 28
Inspection and Test plans are developed by referencing:
- A. The Specification, Safety Manual, Relevant Standards and Codes
- B. The Specification, SDS, relevant Standards and Codes
- C. The Specification, TDS, relevant Standards and Codes
- D. The Specification, Application Guidelines, Relevant Standards and Codes
正解：D
質問 # 29
When conducting inspections the Inspector should follow which standards:
- A. Australian standards in Australia
- B. The specified standards
- C. ISO standards in Europe and Asia
- D. NACE and 55PC standards in North America
正解：B
質問 # 30
......
Senior-Internal-Corrosion-Technologistブレーン問題集PDF、AMPP Senior-Internal-Corrosion-Technologist試験問題詰合せ：https://www.passtest.jp/AMPP/Senior-Internal-Corrosion-Technologist-shiken.html
2025年最新のSenior-Internal-Corrosion-Technologistサンプル問題は信頼され続けるSenior-Internal-Corrosion-Technologistテストエンジン：https://drive.google.com/open?id=1pCueGQrPU35jd9g8moKtTmCDTPZrwysX