[2025年03月最新リリース]Senior-Internal-Corrosion-Technologist問題集でAMPP-SICT認証
最新の完璧なSenior-Internal-Corrosion-Technologist問題集問題と解答で100%パスさせます
質問 # 43
Dehumidification is defined as the removal of moisture vapor from the air to
- A. lower Its temperature.
- B. provide worker comfort
- C. lower Its dew point.
- D. raise its relative humidity.
正解：C
質問 # 44
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Increase the standoff distance
- C. Lower the blast pressure
- D. Move the nozzle quicker
正解：A
質問 # 45
You are the NACE Coating Inspector ona tank lining project where desiccant dehumidificationis being used.
Since the first shift ofabrasive Wasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Advise the coating applicator supervisor of your readings
- B. Call your supervisor
- C. Document the readings at the end of the shift
- D. Check to see if the dehumidification equipment is operating correctly
正解：A
質問 # 46
An Inspection and Test Plan is required when:
- A. When the Inspector requests one
- B. When the Coating Applicator requests one
- C. It is always required
- D. When the Owner specifies one
正解：C
質問 # 47
You are a NACE Level 2 Coaling Inspector who has Just arrived on a Jobin progress where there Is no Inspection and Test Plan (UP). The first morning you arrive the Job is behind schedule and you are asked to take Dry Rim Thickness readings.
Your FIRST preferred course of action is to:
- A. Develop your own methodology and proceed take the readings
- B. Use a generally accepted industry standard and proceed to take readings
- C. Call your supervisor
- D. Refuseto take readings until an ITP isin place
正解：D
質問 # 48
When performing a hardness test on a coating which has elastic properties the inspector is likely to observe:
- A. A very low reading
- B. Cold (low or creep
- C. A very high reading
- D. No difference from any other coating
正解：B
質問 # 49
The Inspectors' goal at the Pre-Job Conference is to:
- A. Take accurate meeting minutes for distribution
- B. Obtain a clear understanding of the Specification
- C. Manage the meeting so it doesn't go off topic
- D. Discuss contractual requirements
正解：B
質問 # 50
Coating surveys may Include which steps? Select All That Apply:
- A. Summarize the collected data
- B. Develop a survey plan
- C. Evaluate the coatings performance
- D. Schedule the remedial work
正解：A、B
質問 # 51
The cost of qualified Coating Inspection Is normally offset by:
- A. Lower Application Costs
- B. Lower Supervision Costs
- C. Lower Coating Life Cycle Costs
- D. Lower Safety Enforcement Costs
正解：C
質問 # 52
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Non-Conductive coatings applied to a conductive metallic substrate
- B. Magnetic coatings applied to a magnetic metallic substrate
- C. Conductive coatings applied to a magnetic metallic substrate
- D. Conductive coatings applied to a cementitious substrate
正解：D
質問 # 53
A reinforced coating is
- A. equally resistant to abrasion and impact as a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. equally resistant to movement and impact as a non-reinforced coating.
正解：C
質問 # 54
All of these ate advantages of using repair patches EXCEPT
- A. barrier to moisture and corrosion.
- B. special tools or equipment are required.
- C. excellent abrasion resistance.
- D. inert to common acids, alkalis, and solvents.
正解：B
質問 # 55
Pre-cleaning of work pieces will NOT remove
- A. snow, ice or water.
- B. oil or grease.
- C. dirt.
- D. mill scale.
正解：D
質問 # 56
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 Inspector when you notice significant documentation errors.
Your FIRST preferred course of action Is to:
- A. Correct the errors yourself and submit the reports without any further action
- B. Correct the errors yourself and suggest the Level 1 inspector be replaced
- C. Correct die errors yourself and advise your supervisor that the Level 1 Inspector Is incompetent
- D. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
正解：D
質問 # 57
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Wetting stage
- B. Flow stage
- C. Getstage
- D. Cure stage
正解：B
質問 # 58
Corrosion Is the reverse process of
- A. flaking.
- B. galvanic deteroration.
- C. steel manufacturing.
- D. hot dipping.
正解：C
質問 # 59
When performing Inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A destructive paint inspection Tooke gauge
- B. A mechanical adhesion tester
- C. A set of 14 pencils of varying hardness
- D. A hardness tester
正解：A
質問 # 60
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Different than air blast cleaning
- B. Comparable to air blast cleaning
- C. The same as air blast cleaning
- D. Slightly different to air blast cleaning
正解：C
質問 # 61
External coatings applied to burled pipelines are generally tested for:
- A. Cathodic disbondment
- B. Gloss level
- C. Solvent resistance
- D. Chalking resistance
正解：A
質問 # 62
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide If and when a destructive test is required.
- A. True
- B. False
正解：B
質問 # 63
Linings are used on the interior of pipelines to
- A. provide protection against soil chemicals.
- B. protect the transported product.
- C. reduce magnetic polarity.
- D. afford limited temperature Insulation.
正解：B
質問 # 64
......
最新のSenior-Internal-Corrosion-Technologist試験問題集でAMPP試験トレーニング：https://www.passtest.jp/AMPP/Senior-Internal-Corrosion-Technologist-shiken.html
2025年最新のの問題Senior-Internal-Corrosion-Technologist問題集で最新のAMPP試験を使おう：https://drive.google.com/open?id=1pCueGQrPU35jd9g8moKtTmCDTPZrwysX