[2024年01月12日] 最速準備で試験合格！NS0-184問題の事前予備
NS0-184のPDF問題集リアル2024最近更新された問題
質問 # 22
You are installing a new AFF A400 cluster and need to access the cluster management LIF from a remote subnet with the fully qualified domain name (FQDN) a400.lab.netapp.com.
In this scenario, which two network components must be configured to log in to ONTAP System Manager from the remote subnet? (Choose two.)
- A. route
- B. DNS
- C. VLAN
- D. NTP
正解：A、B
質問 # 23
A customer has a current AFF ASA A700 cluster and they want to expand the cluster by adding a second AFF ASA A700 HA pair.
In this scenario, which step would be required to accomplish this task?
- A. The customer will need to create a separate cluster for the second AFF ASA A700 pair.
- B. Install a BES-53248 cluster switch and convert the AFF ASA A700 from a switchless to switch cluster.
- C. Enable ALUA between the two HA pairs to allow cluster backend traffic.
- D. Install a Brocade FC switch and create zoning between the original cluster and the new cluster.
正解：B
質問 # 24
You completed a 2-node AFF A700 installation according to the poster. You run the disk show -fields owner command and notice that all drives are assigned to node 1.
In this scenario, which tool would you use to access documentation and guidelines to solve the issue?
- A. Active IQ One Collect
- B. Active IQ Unified Manager
- C. NetAppDocs
- D. NET2
正解：C
質問 # 25
You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.
Which statement explains this behavior?
- A. You do not have a default gateway set.
- B. You do not have network discovery enabled.
- C. You do not have IPv6 configuration set.
- D. You do not have a static IP address.
正解：A
質問 # 26
You installed a new pair of Cisco 92300YC cluster switches at a customer's site. Before you install any files on the switch, you want to view the current configuration.
In this scenario, which command would you use to accomplish this task?
- A. show running-config
- B. switchcfgshow
- C. fabricshow
- D. config show
正解：B
質問 # 27
A storage administrator is trying to upgrade a pair of FAS2520s with internal SATA storage to a new 2-node FAS8300 cluster. The storage administrator wants to preserve the existing data.
In this scenario, which two capabilities are available to the storage administrator? (Choose two.)
- A. the ability to pull out the tray of internal disks of the FAS2520s and reseat the tray in the internal storage of the FAS8300s
- B. the ability to move the volumes from the old nodes to the new nodes
- C. the ability to create a 4-node MetroCluster across the four nodes
- D. the ability to convert the FAS2520s to disk shelves and attach them to the new nodes
正解：C、D
質問 # 28
Click the Exhibit button.
What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)
- A. to install cross-site cluster management switches
- B. to provide connectivity for NVRAM over iWARP
- C. to enable SyncMirror replication
- D. to provide a direct connection for the SnapMirror Synchronous (SM-S)
正解：B、D
質問 # 29
You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.
Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)
- A. Use ports with different chipsets.
- B. Use ports from the same NICs.
- C. Use ports from different NICs.
- D. Use ports with the same chipsets.
正解：C、D
質問 # 30
You are deploying an 8-node AFF A700 by using BES-53248 cluster switches. During the installation, you notice that ports higher than 16 are not coming online. You verify that the additional licenses are installed.
Which two additional steps must be taken to bring the additional ports online? (Choose two.)
- A. Reload the switch
- B. Reload the RCF file
- C. Re-enable each port
- D. Reload the firmware
正解：A、B
質問 # 31
Click the Exhibit button.
Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.
In this scenario, what would you tell the customer?
- A. 0
- B. 1
- C. 2
- D. 3
正解：A
質問 # 32
Which logical interface has a fixed firewall policy?
- A. cluster management LIF
- B. intercluster LIF
- C. cluster LIF
- D. data LIF
正解：C
質問 # 33
You are preparing to physically install a new AFF A400 cluster into a customer's racks. All equipment has been delivered to the customer's site.
Which three tools do you need to complete this installation? (Choose three.)
- A. Phillips #2 screwdriver
- B. laptop computer
- C. cable management tray
- D. additional network cables
- E. slide rail kit
正解：A、B、D
質問 # 34
You installed a new 4-node AFF A400 ONTAP 9.8 cluster. The AFF400 controller data ports were automatically discovered by "automatic port placement".
In this scenario, which two ONTAP network settings were automatically configured? (Choose two.)
- A. subnets
- B. broadcast domains
- C. routes
- D. IPspaces
正解：A、C
質問 # 35
Before starting a base installation on an AFF A400, you need to find out the default cluster interconnect ports for the AFF A400 controllers.
In this scenario, which three resources would you use to find this information? (Choose three.)
- A. Active IQ Unified Manager
- B. Hardware Universe (HWU)
- C. AFF FAS Documentation Center
- D. hardware installation setup poster
- E. Interoperability Matrix Tool (IMT)
正解：B、C、D
質問 # 36
You are installing a new AFF A400 cluster for a customer. The customer indicates that they want to take advantage of AutoSupport On Demand.
In this scenario, which AutoSupport transport protocol must you use?
- A. HTTPS
- B. SMTP
- C. HTTP
- D. FTP
正解：A
質問 # 37
Which two switch operating system are supported on ONTAP cluster switches? (Choose two.)
- A. Cisco IOS
- B. Brocade FOS
- C. Broadcom EFOS
- D. Cisco NX-OS
正解：C、D
質問 # 38
You are installing a new six-node ONTAP 9.8 cluster. You have completed the initial configuration of the cluster interconnect switches and the ONTAP cluster.
In this scenario, which feature should you enable?
- A. cluster switch health monitor
- B. IPv6 on all cluster ports
- C. data center bridging protocol
- D. cluster switch logging
正解：A
質問 # 39
Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)
- A. The LIFs must use the default intercluster service policy.
- B. The MTU size must be set to 9000 bytes on all the LIFs used for the cluster peering.
- C. The LIFs must be in dedicated broadcast domains an IPspaces.
- D. At least one LIF per node is required on each cluster.
正解：A、C
質問 # 40
Click the Exhibit button.
You are attempting to add a new ONTAP 9.7 node to your ONTAP 9.8 NetApp cluster. After attempting to add the node, it fails as shown in the exhibit.
What are two nondisruptive ways to add the new node to your ONTAP cluster? (Choose two.)
- A. Upgrade the new node from ONTAP 9.7 to ONTAP 9.8.
- B. Revert the cluster from ONTAP 9.8 to ONTAP 9.7.
- C. Re-initialize all the nodes in the ONTAP cluster with ONTAP 9.7.
- D. Add the node using the -allow-mixed-version- parameter.
正解：A、D
質問 # 41
......
NS0-184問題集と練習テスト（60試験問題)：https://www.passtest.jp/NetworkAppliance/NS0-184-shiken.html
リリースNetwork Appliance NS0-184更新された問題PDF：https://drive.google.com/open?id=1mnXOTKplePuZJY4-W7dDqyNtmRwOHjI4