最新2025年03月22日リアルなNACE-CIP1-001試験問題集解答で有効なNACE-CIP1-001問題集PDF
NACE NACE-CIP1-001試験問題集でPDF問題とテストエンジン
質問 # 43
Which is a component that supplies most of the features and functions of the material?
- A. pigment
- B. solvent
- C. binder
- D. additive
正解：C
質問 # 44
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 100% of the specified maximum thickness
- C. 70% of the specified maximum thickness
- D. 90% of the specified maximum thickness
正解：A
質問 # 45
Check abrasive blast pressure close to the
- A. substrate
- B. compressor
- C. blast pot
- D. blast nozzle
正解：D
質問 # 46
The Inspector should record the serial numbers of inspection instruments:
- A. Each time the instrument is used
- B. Only if the specification requires it
- C. Only if the instrument is suspected of not working properly
- D. Only when verifying accuracy of the instrument
正解：A
質問 # 47
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 5 to 6 mils (125 to 150 microns)
- B. 10 to 12 mils (250 to 300 microns)
- C. 8 to 10 mils (200 to 250 microns)
- D. 6 to 7 mils (150 to 175 microns)
正解：D
質問 # 48
ASTM Standards are applicable:
- A. In Asia
- B. In North America
- C. In the USA
- D. When specified
正解：D
質問 # 49
Removal of surface contaminants is done by:
- A. Abrasive blasting
- B. Waterjetting
- C. A combination of methods
- D. Scarifying
正解：C
質問 # 50
Surface profile describes:
- A. The general condition of the surface required after abrasive blasting
- B. The level of surface roughness required after abrasive blasting
- C. The initial condition of the surface prior to abrasive blasting
- D. The level of surface cleanliness required after abrasive blasting
正解：B
質問 # 51
Galvanic corrosion occurs on which of the following substrates:
- A. Concrete
- B. Wood
- C. Fiberglass Reinforced Plastic
- D. Metal
正解：D
質問 # 52
Upon arrival of coating materials, the inspector should
- A. observe aryl document that the applicator WFT at regular intervals during application.
- B. observe and document the amount of material and batch numbers.
- C. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- D. observe and document time frame and environmental conditions between each coat.
正解：B
質問 # 53
Conventional spray is a good choice when:
- A. High viscosity coatings are being applied
- B. High production rates are required
- C. High quality finishes are required
- D. High transfer efficiency is required
正解：C
質問 # 54
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Placing the gauge along the longitudinal axis
- B. Using a damaged gauge
- C. Dragging a gauge through wet coating
正解：B、C
質問 # 55
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. white metal blast cleaning.
- B. brush-off blast cleaning.
- C. near-white metal blast cleaning.
- D. commercial blast cleaning.
正解：B
質問 # 56
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Conditions E-G
- B. Rust Grades 1-4
- C. Surface Condition H
- D. Rust Grades A-D
正解：D
質問 # 57
Removal of welds splatter is required:
- A. On every job
- B. When NACE/SSPC abrasive blast standards are specified
- C. When specifically identified in the owner's specification
- D. When ISO abrasive blast standards are specified
正解：C
質問 # 58
Stripe coats are best applied by:
- A. Conventional spray
- B. Airless spray
- C. High volume low pressure spray
- D. Brush
正解：D
質問 # 59
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Meet with the prospective employer to determine the scope of your role
- C. Advise the prospective employer that you cannot accept the position
- D. Accept the assignment without hesitation
正解：B
質問 # 60
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
正解：B
質問 # 61
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks and just record the same readings as you have been getting
- B. Skip the checks as you are. confident the blast pressure is OK
- C. Keep doing the checks and consult the Owner's representative for direction
- D. Keep doing the checks regardless
正解：C
質問 # 62
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Chloride salt may produce a false positive
- B. Ultra-Violet light may contaminant the surface
- C. Synthetic oil or grease may not be identified
- D. Presence of weld spatter may produce a false positive
正解：C
質問 # 63
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. dry film thickness (DEI) measurement.
- B. vial lest.
- C. wet film thickness (WFT) measurement.
- D. blotter test for the presence of oil and water.
正解：D
質問 # 64
The initial steel condition is important to the NACE Inspector because:
- A. If the steel is pitted more coating will be required
- B. Less abrasive is need if the mill Scale s gone
- C. It affects the final appearance after blasting
- D. The Inspector may have to reject the Steel
正解：D
質問 # 65
......
NACE-CIP1-001試験は、コーティング検査における個人の知識とスキルを評価する包括的なテストです。この試験は、4時間の時間枠内に完了する必要がある120の複数選択質問で構成されています。質問は、コーティング検査手順、表面調製技術、および適用方法に関する個人の理解をテストするために設計されています。この試験は、グローバルな視聴者に応えるために複数の言語で提供されます。
信頼できるCIP Level 1 NACE-CIP1-001問題集PDF2025年03月22日最近更新された問題：https://www.passtest.jp/NACE/NACE-CIP1-001-shiken.html
最新NACE-CIP1-001試験問題集には合格保証付きます：https://drive.google.com/open?id=1VGLx7HyDTGPwUuroedmfnCZB4CdLoCqC