最新2025年05月06日リアルなNACE-CIP1-001試験問題集解答で有効なNACE-CIP1-001問題集PDF
NACE NACE-CIP1-001試験問題集でPDF問題とテストエンジン
NACE-CIP1-001（コーティングインスペクターレベル1）試験は、コーティング検査の分野で働く個人の知識とスキルを評価するために設計された認定プログラムです。この試験は、全米腐食エンジニア協会（NACE）によって管理されており、コーティング検査業界の基準としてグローバルに認識されています。認定プログラムは、表面の準備、コーティングの適用、およびアプリケーション後の検査を含む、コーティング検査の基礎に関する申請者の理解をテストする厳格なプロセスです。
質問 # 23
Whenever dissimilar metals must join, the most common practice is to
- A. provide anodic protection to prevent corrosion.
- B. provide cathodic protection to prevent corrosion,
- C. avoid coating all connected dissimilar metals.
- D. coat all connected dissimilar metals.
正解：D
質問 # 24
Dew point is the temperature at which
- A. the air is saturated.
- B. water freezes.
- C. humidity decreases
- D. condensation occurs.
正解：D
質問 # 25
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades A-D
- B. Surface Condition H
- C. Surface Conditions E-G
- D. Rust Grades 1-4
正解：A
質問 # 26
Which is a component that supplies most of the features and functions of the material?
- A. solvent
- B. binder
- C. pigment
- D. additive
正解：B
質問 # 27
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- B. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- C. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
正解：A
質問 # 28
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 3
- B. Level 1
- C. Level 4
- D. Level 2
正解：A
質問 # 29
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 millimeters (.10 inch)
- B. 1 cm (.39 inch)
- C. 6.35 cm (2.5 inch)
- D. 2.5 cm (1 inch)
正解：D
質問 # 30
Corrosion generally occurs at which of the following sites:
- A. Cathode
- B. Metallic pathway
- C. Electrolyte
- D. Anode
正解：D
質問 # 31
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he cannot proceed
- B. Advise the Contractor he can proceed
- C. Call your supervisor
- D. Advise the Contractor of your readings
正解：D
質問 # 32
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 225 Gauge Readings resulting in 75 Spot Measurements
- C. 105 Gauge Readings resulting in 35 Spot Measurements
- D. 45 Gauge readings resulting in 15 Spot Measurements
正解：B
質問 # 33
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. perform additional tests secretly to ensure there are no other potential issues at the site
正解：C
質問 # 34
Silicone coatings are typically:
- A. Used as a sacrificial primer
- B. Used strictly in immersion service
- C. Applied in very thick films
- D. Applied in very' thin films
正解：D
質問 # 35
A magnetic pull-off type gauge is a good choice when:
- A. Performing an adhesion test
- B. When working on non-ferrous metals
- C. Accuracy is not required
- D. When an intrinsically safe tool is required
正解：D
質問 # 36
Inspection documentation is important because:
- A. a) only
- B. a) & b)
- C. It is the only deliverable item provided by the inspector
- D. Owners use the documentation for a variety of purposes
正解：D
質問 # 37
Which of these tests uses a syringe?
- A. Soluble salts meter
- B. Bresle patch
- C. Sleeve test
- D. Potassium ferricyanide
正解：B
質問 # 38
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. telegraphing.
- B. transitioning.
- C. juxtaposing.
- D. monitoring
正解：A
質問 # 39
An Inspector should change position when:
- A. The Inspector is convinced by verifiable facts
- B. The Inspectors position is not the majority position
- C. Only when directed by the supervisor
- D. The Owner can save some money by the change
正解：A
質問 # 40
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A method to grade surface profile
- B. A final conflict resolution method
- C. A general guide
- D. Pass/fail criteria
正解：C
質問 # 41
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. brush-off blast cleaning.
- B. commercial blast cleaning.
- C. white metal blast cleaning.
- D. near-white metal blast cleaning.
正解：A
質問 # 42
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks and just record the same readings as you have been getting
- B. Keep doing the checks regardless
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Keep doing the checks and consult the Owner's representative for direction
正解：D
質問 # 43
......
信頼できるCIP Level 1 NACE-CIP1-001問題集PDF2025年05月06日最近更新された問題：https://www.passtest.jp/NACE/NACE-CIP1-001-shiken.html
最新NACE-CIP1-001試験問題集には合格保証付きます：https://drive.google.com/open?id=1GbKKh5Rct6YAZODbSnF_8mZJ96Pizplg