準備できるNACE-CIP1-001問題解答は無料更新されて100%試験合格保証 [2025]
問題集リアルなNACE NACE-CIP1-001試験問題 [更新されたのは2025年]
NACE-CIP1-001認定試験は、コーティング検査官としてのキャリアを追求したい個人を対象としています。これは、コーティングと腐食防止の分野における個人の知識とスキルを示す、国際的に認められた認定資格です。認定試験は、腐食制御業界の専門家にトレーニング、認定、およびネットワーキングの機会を提供する専門組織であるNational Association of Corrosion Engineers (NACE)によって実施されます。
NACE-CIP1-001認定試験は、コーティング検査技術、表面の準備、コーティング、および検査機器に関する個人の知識をテストするように設計されています。試験は、筆記試験と実用的な試験の2つの部分に分かれています。筆記試験は、120の複数選択の質問で構成され、コーティング検査に関連するさまざまなトピックをカバーしています。実際の試験は、実際の環境で知識を適用する個人の能力を評価するように設計されています。
NACE-CIP1-001認定は、コーティング業界の個人と企業の両方にとって重要です。個人にとって、認定はこの分野での専門知識とプロフェッショナリズムを実証し、雇用機会の増加と給与の増加につながる可能性があります。企業の場合、NACE認定のコーティング検査官を雇用することで、プロジェクトが最高水準に完了することを保証します。これにより、より多くのビジネスを獲得し、費用のかかる間違いを避けることができます。
質問 # 42
SSPC SP 1 identifies the use of:
- A. Inorganic solvents
- B. A wide variety of materials
- C. Biodegradable detergents
- D. Organic solvents
正解：B
質問 # 43
According to SSPC PA 2 a Spot Measurement is:
- A. A single gauge reading
- B. The average of gauge readings taken in a 4cm (1.5 inch) circle
- C. The overall average of all readings
- D. The average of all spot measurements in a given area
正解：B
質問 # 44
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. At all times
- B. In the field only
- C. Only if the specification requires it
- D. In the office only
正解：A
質問 # 45
Silicone coatings are typically:
- A. Used strictly in immersion service
- B. Used as a sacrificial primer
- C. Applied in very' thin films
- D. Applied in very thick films
正解：C
質問 # 46
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 8 to 10 mils (200 to 250 microns)
- B. 5 to 6 mils (125 to 150 microns)
- C. 6 to 7 mils (150 to 175 microns)
- D. 10 to 12 mils (250 to 300 microns)
正解：C
質問 # 47
Inspector's daily reports are used:
Select All That Apply
- A. To provide continuity between inspectors
- B. By the contractor to estimate the amount of work done that day
- C. To aid in arbitration between the contractor and client
- D. To help in cases of a coating failure
正解：A、B、C、D
質問 # 48
Safety Data Sheets must be carefully reviewed by:
- A. All personnel involved in the job
- B. The Owner's personnel
- C. The Application personnel
- D. The Inspection personnel
正解：A
質問 # 49
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. The Inspector will improve job flow and schedule
- C. The inspection cost will be offset by an improvement in service life
- D. a) and c)
正解：D
質問 # 50
Removal of surface contaminants is done by:
- A. A combination of methods
- B. Abrasive blasting
- C. Waterjetting
- D. Scarifying
正解：A
質問 # 51
ISO SA 2.5 is defined as:
- A. Very Thorough Blast Cleaning
- B. Light Blast Cleaning
- C. Thorough Blast Cleaning
- D. Near White Metal Blasting
正解：A
質問 # 52
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 6.35 cm (2.5 inch)
- B. 2.5 millimeters (.10 inch)
- C. 2.5 cm (1 inch)
- D. 1 cm (.39 inch)
正解：C
質問 # 53
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. sagging.
- B. cracking.
- C. holiday.
- D. checking.
正解：C
質問 # 54
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- B. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
正解：A
質問 # 55
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Call your supervisor
- C. Advise the Contractor he can proceed
- D. Advise the Contractor he cannot proceed
正解：A
質問 # 56
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When specifically identified in the owner's specification
- C. On every job
- D. When ISO abrasive blast standards are specified
正解：B
質問 # 57
ASTM Standards are applicable:
- A. In the USA
- B. In North America
- C. In Asia
- D. When specified
正解：D
質問 # 58
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Placing the gauge along the longitudinal axis
- B. Using a damaged gauge
- C. Dragging a gauge through wet coating
正解：B、C
質問 # 59
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Power tools
- B. Abrasive blast nozzles
- C. Airless spray equipment
- D. Hand tools
正解：A
質問 # 60
An Inspector should change position when:
- A. Only when directed by the supervisor
- B. The Owner can save some money by the change
- C. The Inspector is convinced by verifiable facts
- D. The Inspectors position is not the majority position
正解：C
質問 # 61
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks as you are. confident the blast pressure is OK
- B. Skip the checks and just record the same readings as you have been getting
- C. Keep doing the checks and consult the Owner's representative for direction
- D. Keep doing the checks regardless
正解：C
質問 # 62
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades 1-4
- B. Surface Condition H
- C. Surface Conditions E-G
- D. Rust Grades A-D
正解：D
質問 # 63
......
NACE-CIP1-001試験問題集、NACE-CIP1-001練習テスト問題：https://www.passtest.jp/NACE/NACE-CIP1-001-shiken.html
無料NACE-CIP1-001試験問題集で合格させるお手軽に試験合格：https://drive.google.com/open?id=1OW9Afvo65cJWj4VxlVYaoDoRQ5XuAo46