NACE-CIP1-001ブレーン問題集リアル試験最新問題2025年12月28日には100問題
最新NACE-CIP1-001のPDF問題集リアル無料テスト本日更新です
質問 # 33
A NACE Coating Inspector is permitted to transport coating material when:
- A. The Inspector should never transport coating material
- B. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- C. Asked to do so by the Coating Application team
- D. Asked to do so by the Owner's Representative
正解：A
質問 # 34
In a non-convertible coating the role of the primary solvent is to:
- A. To promote faster cure
- B. To control the evaporation rate
- C. To dissolve the resin
- D. To make the coating flow out better
正解：B
質問 # 35
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 45 Gauge readings resulting in 15 Spot Measurements
- B. 75 Gauge Readings resulting in 25 Spot Measurements
- C. 225 Gauge Readings resulting in 75 Spot Measurements
- D. 105 Gauge Readings resulting in 35 Spot Measurements
正解：C
質問 # 36
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Skip the checks and just record the same readings as you have been getting
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Keep doing the checks regardless
正解：A
質問 # 37
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 3
- B. Level 2
- C. Level 1
- D. Level 4
正解：A
質問 # 38
What is used to determine compressed air cleanliness?
- A. Needle pressure gauge
- B. Psychrometer
- C. Blotter test
- D. Profilometer
正解：D
質問 # 39
Prior to using Inspection Tools the inspector must:
- A. a), b) & c)
- B. Be trained on how to use the instrument
- C. Ensure the instrument is within calibration parameters
- D. Read the manufactures' instructions
正解：A
質問 # 40
Passivation can best be described as:
- A. A coating layer applied to the surface to inhibit corrosion
- B. Complete elimination pf the corrosion process
- C. Treating metal with a liquid inhibiter
- D. A protective metallic oxide surface layer that slows corrosion
正解：D
質問 # 41
Osmotic blistering is most likely to occur as a result of
- A. airless spray application
- B. inadequate anchor pattern/surface profile.
- C. applying tine coating too thin.
- D. overcoating a surface contaminated with chemical salts.
正解：A
質問 # 42
Daily reports are important because:
Select All That Apply
- A. the information impacts future projects.
- B. Management uses them to make personnel decisions.
- C. Inspectors rarely change on a project.
- D. The information aids communication with supervisors.
正解：A、B、D
質問 # 43
Safety Data Sheets must be carefully reviewed by:
- A. All personnel involved in the job
- B. The Inspection personnel
- C. The Owner's personnel
- D. The Application personnel
正解：A
質問 # 44
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Go with the majority opinion
- B. Achieve consensus through negotiation
- C. Call the supervisor
- D. Never change his/her mind
正解：C
質問 # 45
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. damages structural elements thereby speeding up the corrosion process.
- B. develops a polished surface, which is a poor anchor profile for most coatings
- C. scratches the surface too deeply resulting in uneven coating application
- D. develops a good anchor profile resulting in uneven coating application.
正解：B
質問 # 46
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept the assignment without hesitation
- B. Advise the prospective employer that you cannot accept the position
- C. Meet with the prospective employer to determine the scope of your role
- D. Review the NACE Attestation prior to making a decision
正解：C
質問 # 47
SSPC SP 1 identifies the use of:
- A. Organic solvents
- B. A wide variety of materials
- C. Inorganic solvents
- D. Biodegradable detergents
正解：B
質問 # 48
Check abrasive blast pressure with a
- A. replica tape
- B. surface comparator
- C. nozzle aperature gauge
- D. needle pressure gauge
正解：D
質問 # 49
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Abrasive blast nozzles
- B. Power tools
- C. Airless spray equipment
- D. Hand tools
正解：B
質問 # 50
Non Conformance Reports are completed by the Inspector:
- A. When the Inspector deems it to be a significant non-conforming item
- B. In every instance that an item does not meet the specification requirements
- C. In accordance with the specification's definition of a non-conformance
- D. When the Inspector and Contractor deem it to be a significant non-conforming item
正解：D
質問 # 51
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Purchase Professional Liability Insurance prior to job commencement
- D. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
正解：D
質問 # 52
Dew point is the temperature at which
- A. the air is saturated.
- B. condensation occurs.
- C. water freezes.
- D. humidity decreases
正解：B
質問 # 53
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. NACE 2/SSPC SP10
- B. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- C. a detailed checklist and document the lack of a standard.
- D. their best judgment based on similar projects and specifications.
正解：B
質問 # 54
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Anode
- C. Cathode
- D. Reference Cell
正解：D
質問 # 55
Corrosion generally occurs at which of the following sites:
- A. Electrolyte
- B. Cathode
- C. Anode
- D. Metallic pathway
正解：C
質問 # 56
Solvents are added to coating formulations to
- A. increase film permeability.
- B. dissolve binders and form liquid coatings.
- C. provide color.
- D. decrease film permeability.
正解：B
質問 # 57
......
NACE-CIP1-001認定試験は、75年以上にわたって腐食対策分野の専門家に教育と認定プログラムを提供している非営利団体であるNational Association of Corrosion Engineers（NACE）によって提供されます。この認定試験は、世界的に認められ、業界の雇用主に高く評価されています。
NACE-CIP1-001問題集には100%厳密検証された問題と解答で合格保証もしくは全額返金：https://www.passtest.jp/NACE/NACE-CIP1-001-shiken.html
合格させるNACE NACE-CIP1-001試験には練習テスト問題集豪華お試しセット：https://drive.google.com/open?id=1D91S63Px9KEdoMz3x28G9s0B0IVx5jdE