2025年最新のに更新された検証済みのNACE-CIP1-001問題集と解答で合格保証もしくは全額返金
NACE-CIP1-001のPDF問題とテストエンジンには100問があります
NACE（National Association of Corrosion Engineers）Internationalは、腐食防止と制御に特化した専門団体です。NACEは、塗装検査員のための認定プログラムであるCoating Inspector Program（CIP）を提供しています。このプログラムには3つのレベルがあり、レベル1は入門レベルの認定資格です。NACE-CIP1-001試験は、レベル1の塗装検査員のための認定試験です。
NACE-CIP1-001（コーティングインスペクターレベル1）認定試験は、コーティング検査における個人の知識とスキルを評価する世界的に認められた認定です。この認定は、腐食制御業界に特化した専門組織であるNACE Internationalによって提供されています。この試験は、コーティング検査の原則、表面の準備、コーティングの適用、および品質管理に関する候補者の理解を評価するように設計されています。この認定は、コーティング業界でのキャリアを進歩させようとする個人や、フィールドに入ろうとする人にとって不可欠です。
NACE-CIP1-001認定は、コーティング業界の個人と企業の両方にとって重要です。個人にとって、認定はこの分野での専門知識とプロフェッショナリズムを実証し、雇用機会の増加と給与の増加につながる可能性があります。企業の場合、NACE認定のコーティング検査官を雇用することで、プロジェクトが最高水準に完了することを保証します。これにより、より多くのビジネスを獲得し、費用のかかる間違いを避けることができます。
質問 # 25
Whenever dissimilar metals must join, the most common practice is to
- A. provide anodic protection to prevent corrosion.
- B. avoid coating all connected dissimilar metals.
- C. coat all connected dissimilar metals.
- D. provide cathodic protection to prevent corrosion,
正解：C
質問 # 26
The most important factor resulting in improved job site safety is:
- A. Situational Awareness
- B. Engineering Controls
- C. Safety Enforcement
- D. Personal Protective Equipment
正解：A
質問 # 27
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. Yes, because the 'two standards are not equivalent
- B. No, because there is no real difference in the standards
- C. It depends on which hand tool the Contractor selects
- D. It depends on which power tool the Contractor selects
正解：B
質問 # 28
SSPC SP 1 identifies the use of:
- A. Organic solvents
- B. Inorganic solvents
- C. Biodegradable detergents
- D. A wide variety of materials
正解：D
質問 # 29
If inspectors identify issues of non-conformance during an inspection, they should
- A. perform additional tests secretly to ensure there are no other potential issues at the site
- B. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- C. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- D. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
正解：D
質問 # 30
Galvanic corrosion occurs on which of the following substrates:
- A. Wood
- B. Concrete
- C. Fiberglass Reinforced Plastic
- D. Metal
正解：D
質問 # 31
Which is a component that supplies most of the features and functions of the material?
- A. solvent
- B. binder
- C. pigment
- D. additive
正解：B
質問 # 32
The main responsibilities of the inspector are to
- A. observe and direct the work of the contractors.
- B. direct and perform the work stated in the specification.
- C. observe and report the quality of the work performed.
- D. demonstrate to the contractor how to apply the coating.
正解：C
質問 # 33
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. brush-off blast cleaning.
- B. near-white metal blast cleaning.
- C. white metal blast cleaning.
- D. commercial blast cleaning.
正解：A
質問 # 34
Inspection documentation is important because:
- A. Owners use the documentation for a variety of purposes
- B. It is the only deliverable item provided by the inspector
- C. a) & b)
- D. a) only
正解：A
質問 # 35
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks regardless
- B. Skip the checks as you are. confident the blast pressure is OK
- C. Skip the checks and just record the same readings as you have been getting
- D. Keep doing the checks and consult the Owner's representative for direction
正解：D
質問 # 36
Daily reports are important because:
Select All That Apply
- A. Inspectors rarely change on a project.
- B. the information impacts future projects.
- C. The information aids communication with supervisors.
- D. Management uses them to make personnel decisions.
正解：B、C、D
質問 # 37
Prior to using Inspection Tools the inspector must:
- A. Read the manufactures' instructions
- B. Ensure the instrument is within calibration parameters
- C. a), b) & c)
- D. Be trained on how to use the instrument
正解：C
質問 # 38
ASTM Standards are applicable:
- A. In Asia
- B. In North America
- C. In the USA
- D. When specified
正解：D
質問 # 39
Removal of welds splatter is required:
- A. On every job
- B. When specifically identified in the owner's specification
- C. When ISO abrasive blast standards are specified
- D. When NACE/SSPC abrasive blast standards are specified
正解：B
質問 # 40
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he cannot proceed
- B. Advise the Contractor of your readings
- C. Advise the Contractor he can proceed
- D. Call your supervisor
正解：B
質問 # 41
......
試験エンジンはNACE-CIP1-001試験無料お試しサンプル365日更新されます：https://www.passtest.jp/NACE/NACE-CIP1-001-shiken.html
テストエンジンの練習テストならこれNACE-CIP1-001有効で更新された問題集：https://drive.google.com/open?id=1jE1QrSEiT07UgurqwJcqkaBcP0_pb-AE