必ず合格できるNACE NACE-CIP2-001試験の正確な100問題と解答あります
最新 [2025年07月08日]2025年最新の実際にある検証済みのNACE-CIP2-001問題集
試験は、筆記試験と実践試験の2つの部分で構成されています。筆記試験は、コーティング検査に関連するさまざまなトピックをカバーする120の複数選択の質問で構成されています。実際の試験には、コーティング検査と品質管理手順を実行する候補者の能力の実践的なテストが含まれます。実際の試験は実験室の環境で実施されており、候補者がさまざまな検査ツールや機器を使用する習熟度を実証することを要求します。
質問 # 15
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Express a willingness to work with the site team and follow the specification
- B. Suggest to the Owner that the supervisor should be removed from site
- C. Defend the previous inspector
- D. Challenge the supervisor's authority
正解：A
質問 # 16
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It will result in a very slippery surface
- C. It contains biocide
- D. It doesn't contain biocide
正解：C
質問 # 17
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Tooke Gauge
- B. Magnetic Gauge
- C. Eddy Current Gauge
- D. Ultra Sonic DFT Gauge
正解：A
質問 # 18
Inspector reports should always be copied to:
- A. Whomever the Owner identifies
- B. The Owner only
- C. All parties involved in the project
- D. The Contractor and Owner
正解：A
質問 # 19
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Do not complete your report until they can be found
- B. Re-create the reports as not much was going on during night shift anyway
- C. Use creative writing to cover over the fact they are missing
- D. Plainly state in your report that they are missing
正解：D
質問 # 20
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. mixed with uncontaminated abrasive
- B. washed with clean potable water prior to Use.
- C. disposed of properly.
- D. run through the air wash separator.
正解：C
質問 # 21
Examples of non-ferrous metals include
Select All that Apply:
- A. copper
- B. mild steel.
- C. aluminum
- D. iron
正解：A、C
質問 # 22
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that another NACE Inspector would understand
- B. Language that the most would understand
- C. Language that only technical experts would understand
- D. Language that only in the project would understand
正解：B
質問 # 23
When ASIN D 3363 is specified the Inspector must:
- A. Record the two end points identified in the standard
- B. Use the correct solvent
- C. Record the highest value attained
- D. Record the percentage of failure
正解：A
質問 # 24
A reinforced coating is
- A. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. equally resistant to movement and impact as a non-reinforced coating.
- D. equally resistant to abrasion and impact as a non-reinforced coating.
正解：A
質問 # 25
NACE Standards include:
- A. a) & b)
- B. Standard Practices
- C. Material Requirements
- D. a) only
正解：A
質問 # 26
A single component water borne acrylic coating cures by:
- A. Solvent Evaporation
- B. Co-Reaction
- C. Coalescence
- D. Oxidation
正解：C
質問 # 27
Coating Surveys are legally required:
- A. On water tanks and potable water pipelines
- B. On commercial marine vessels and offshore platforms
- C. On food and beverage vessels and can linings
- D. On high pressure gas lines and fireproofed structures
正解：B
質問 # 28
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Advise the prospective employer that you cannot accept the position
- B. Review the NACE Attestation prior to making a decision
- C. Accept assignment without hesitation
- D. Meet with the prospective employer to scope of your role
正解：B
質問 # 29
Inspection and Test Plans are provided to:
- A. To supersede the requirements of the product data sheets
- B. So the contractor has a single document to reference
- C. Outline the inspection steps, sequencing and pass/fail criteria
- D. So the Inspector doesn't have to read the entire specification
正解：C
質問 # 30
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Fusion Bonded Epoxy
- B. 3-Layer Polyethylene (PE)
- C. Coal Tar Enamel
- D. 2-Layer Polyethylene (PE)
正解：B
質問 # 31
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Inspector to decide which one to follow
- B. The Specification prevails
- C. The Product Data Sheet prevails
- D. It is up to the Applicator to decide which one to follow
正解：B
質問 # 32
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Iron content
- B. Cost
- C. Safety
- D. Appearance
正解：A
質問 # 33
Individuals conducting Coating Surveys should:
- A. Always be NACE or SSPC Protective coating Specialists
- B. Always be trained and experienced Coating Industry
- C. Always be NACE Level 3 Certified Inspectors
- D. Always be experienced Specification Writers
正解：B
質問 # 34
Generally for safety considerations, waterjetting hose connections use
- A. a whip-lock device.
- B. an oil/water separator.
- C. filters.
- D. a long wand.
正解：A
質問 # 35
......
NACE-CIP2-001コーティングインスペクターレベル2試験は、業界での知識とスキルを証明したいコーティング検査の専門家にとって重要な認定試験です。この認定試験は、求職市場で競争力を持ち、コーティングが最高水準で適用および検査され、より安全で効率的な運用が実現されることを保証します。
無料でゲット！2025年最新のに更新されたNACE NACE-CIP2-001試験問題と解答：https://www.passtest.jp/NACE/NACE-CIP2-001-shiken.html
合格させるNACE-CIP2-001試験には更新された100問題あります：https://drive.google.com/open?id=1ks_hxpA0tTwbLyVEPu98vg7OG288cYYg