NACE NACE-CIP2-001最新問題集[2023]高得点を掴み取れ
NACE-CIP2-001問題集PassTest100%合格率保証
NACE-CIP2-001認定試験は、候補者がコーティング技術と検査技術を深く理解する必要がある挑戦的な試験です。経験豊富なコーティング検査官の知識とスキルをテストし、安全かつ効果的に仕事をするために必要な専門知識を確保するように設計されています。この試験はNACE Internationalによって管理されており、世界中のさまざまな場所で提供されています。試験に合格した候補者には、NACE-CIP2-001認定が授与されます。これは、コーティング業界の卓越性の印です。
質問 # 14
A reinforced coating is
- A. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. equally resistant to movement and impact as a non-reinforced coating.
- C. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. equally resistant to abrasion and impact as a non-reinforced coating.
正解：A
質問 # 15
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Safety Enforcement Costs
- B. Lower Application Costs
- C. Lower Coating Life Cycle Costs
- D. Lower Supervision Costs
正解：C
質問 # 16
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Request that the Contractor re-blast the floor
- C. Review the standard with the Contractor and re-inspect the floor
- D. Shut the job down
正解：C
質問 # 17
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Defend the previous inspector
- B. Express a willingness to work with the site team and follow the specification
- C. Challenge the supervisor's authority
- D. Suggest to the Owner that the supervisor should be removed from site
正解：B
質問 # 18
The HATE adhesion tester uses
- A. compressed air to apply pressure to the test dolly.
- B. a hydraulic piston to apply pressure to the test dolly.
- C. mechanical means only to apply pressure to the test dolly.
- D. a special tape to apply pressure to the test dolly.
正解：B
質問 # 19
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of skin
- B. Risk of chemical exposure
- C. a), b), and c)
- D. Risk of acid or caustic splashes
正解：C
質問 # 20
Dehumidification is defined as the removal of moisture vapor from the air to
- A. provide worker comfort.
- B. lower its temperature
- C. lower its dew point,
- D. raise its relative humidity.
正解：C
質問 # 21
You should bulk store coatings containing isocyanates
- A. in a well ventilated area separate from the work place.
- B. wherever it is convenient
- C. in a refrigerated warehouses
- D. in a heated warehouse.
正解：A
質問 # 22
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Level 3 Inspector
- B. Another NACE Level 2 Inspector
- C. A NACE Protective Coating Specialist
- D. A NACE Level 1 Inspector
正解：A
質問 # 23
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the percentage of failure
- C. Record the two end points identified in the standard
- D. Record the highest value attained
正解：C
質問 # 24
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Request a re-blast of the item in question
- B. Review the NCR with the other Inspector
- C. Consult your supervisor
- D. Verbally challenge the NCR
正解：C
質問 # 25
Cold-applied tape
- A. are identifiable by its distinct colors, usually light blue, green, Or Grey.
- B. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- C. have a cross-linked polyethylene backing and a heat-activated adhesive.
- D. is typically green or led and looks like "painted" finish.
正解：B
質問 # 26
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Appearance
- B. Safety
- C. Iron content
- D. Cost
正解：C
質問 # 27
Coating application to concrete substrates is:
- A. More challenging than coating steel
- B. Not required as Concrete is inorganic
- C. The same as coating steel
- D. Less challenging, than coating steel
正解：A
質問 # 28
Generally for safety considerations, waterjetting hose connections use
- A. a long wand.
- B. a whip-lock device.
- C. filters.
- D. an oil/water separator.
正解：B
質問 # 29
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Comparable to air blast cleaning
- B. Different than air blast cleaning
- C. Slightly different to air blast cleaning
- D. The same as air blast cleaning
正解：D
質問 # 30
......
NACE-CIP2-001試験には、コーティング仕様や基準、表面処理、コーティングの施工方法、検査技術、防食など、幅広いトピックが含まれています。合格者はまた、プロジェクト仕様書、図面、検査報告書などの技術文書を解釈する能力を示す必要があります。
NACE-CIP2-001試験は、石油・ガス、石油化学、海洋、建設など多くの産業で塗装検査認定の標準として認められています。この認定は非常に尊敬されており、塗装産業での雇用に必要な要件としてしばしば使用されています。この認定を取得することで、高度な専門知識と業界へのコミットメントを証明し、この分野のプロフェッショナルにとって貴重な資産となります。
100%合格率リアルNACE-CIP2-001試験成功を掴み取れ：https://www.passtest.jp/NACE/NACE-CIP2-001-shiken.html
プレミアム良質なNACE NACE-CIP2-001オンライン問題集：https://drive.google.com/open?id=1wFm-dBbc-UErBcAG3e1urT80Fus73ry2