[2024年更新]合格できるNACE-CIP2-001試験にはリアルな問題解答
NACE-CIP2-001試験問題ゲット最新[2024]と正解回答
質問 # 38
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 25 double rubs with a saturated cloth.
- B. 50 double rubs with a saturated cloth.
- C. 25 single rubs with a saturated cloth.
- D. 35 single rubs with a saturated cloth.
正解：B
質問 # 39
A reinforced coating is
- A. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. equally resistant to abrasion and impact as a non-reinforced coating.
- C. equally resistant to movement and impact as a non-reinforced coating.
- D. less resistant to movement, abrasion, and impact than a non-reinforced coating.
正解：A
質問 # 40
The Inspectors' goal at the Pre-Job Conference is to:
- A. Take accurate meeting minutes for distribution
- B. Discuss contractual requirements
- C. Manage the meeting so it doesn't go off topic
- D. Obtain a clear understanding of the Specification
正解：D
質問 # 41
Cold-applied tape
- A. have a cross-linked polyethylene backing and a heat-activated adhesive.
- B. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- C. is typically green or led and looks like "painted" finish.
- D. are identifiable by its distinct colors, usually light blue, green, Or Grey.
正解：B
質問 # 42
Inspector reports should always be copied to:
- A. Whomever the Owner identifies
- B. All parties involved in the project
- C. The Owner only
- D. The Contractor and Owner
正解：A
質問 # 43
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Gathering
- B. Midstream
- C. Transmission
- D. Distribution
正解：D
質問 # 44
The primary purpose of Fireproofing coatings are to provide:
- A. fire extinguishing characteristics
- B. Temporary protection for the structure
- C. Explosion resistance
- D. Preferential fuel for the fire
正解：B
質問 # 45
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by caustic etching
- B. SP 1 followed by SP 3
- C. SP 1 followed by SP 2
- D. SP 1 followed by acid etching
正解：C
質問 # 46
A single component water borne acrylic coating cures by:
- A. Coalescence
- B. Solvent Evaporation
- C. Co-Reaction
- D. Oxidation
正解：A
質問 # 47
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Review the standard with the Contractor and re-inspect the floor
- B. Request that the Contractor re-blast the floor
- C. Shut the job down
- D. Call your supervisor
正解：A
質問 # 48
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very low reading
- B. No difference from any other coating
- C. Cold flow or creep
- D. A very high reading
正解：C
質問 # 49
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Comparable to air blast cleaning
- B. Slightly different to air blast cleaning
- C. The same as air blast cleaning
- D. Different than air blast cleaning
正解：C
質問 # 50
NACE No.13/ SSPC 6 identifies the use of:
- A. Steam cleaning only
- B. Watterjetting only
- C. Various methods of cleaning
- D. Abrasive blasting only
正解：C
質問 # 51
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Tooke Gauge
- B. Magnetic Gauge
- C. Eddy Current Gauge
- D. Ultra Sonic DFT Gauge
正解：A
質問 # 52
Coating surveys may include which steps?
Select All That Apply:
- A. Develop a survey plan
- B. Evaluate the coatings performance
- C. Schedule the remedial work
- D. Summarize the collected data
正解：A、B、C、D
質問 # 53
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
正解：B
質問 # 54
......
練習できるNACE-CIP2-001問題で認証試験問題集ガイド解答は練習専門PassTest：https://www.passtest.jp/NACE/NACE-CIP2-001-shiken.html
無料NACE NACE-CIP2-001テスト練習テスト問題試験問題集：https://drive.google.com/open?id=1wFm-dBbc-UErBcAG3e1urT80Fus73ry2