ASQ CQE問題集で100%カバー率リアル試験問題（更新された162問あります)
リアルCQE問題集でリアルASQ問題集PDF
ASQ CQE 認定試験の出題範囲：
| トピック | 出題範囲 |
|---|---|
| トピック 1 |
|
| トピック 2 |
|
| トピック 3 |
|
| トピック 4 |
|
| トピック 5 |
|
| トピック 6 |
|
| トピック 7 |
|
| トピック 8 |
|
| トピック 9 |
|
質問 16
To be effective, a corrective and preventive action system must have
- A. A material review board.
- B. Approved of the QC department.
- C. Top management support.
- D. A method for identifying nonconformities.
正解: D
質問 17
If the probability of a success on a single trial is 0.2 and 3 trials are performed, what is the probability of at least one success?
- A. 0.600
- B. 0.384
- C. 0.008
- D. 0.488
正解: D
質問 18
Given the data below, what is the 90% confidence interval for the variance?
22, 23, 19, 17, 29, 25
- A. 4.21 - 99.07
- B. 16.87 - 56.52
- C. 8.27 - 79.88
- D. 15.32 - 28.66
正解: C
解説:
Explanation/Reference:
質問 19
The AQL for a given sampling plan is 1% this means that
- A. The producer takes a small risk of rejecting product which is 1% defective or better.
- B. All lots are 1% defective or better.
- C. All accepted lots are 1% defective or better.
- D. The average quality level of the plan is 1%.
正解: A
質問 20
A system was designed with 3 capacitors. When the system is first activated all capacitors are operating. The system continues to operate as long as at least 1 capacitor is operating. This is an example of
- A. A series system.
- B. A standby parallel system.
- C. Redundancy.
- D. An active parallel system.
正解: D
質問 21
A process has been experiencing problems lately. The operators charting the process have identified the cause to be due to a change in incoming materials. This problem is
- A. A common cause.
- B. A normal event.
- C. A special cause.
- D. Attributed to purchasing.
正解: C
質問 22
If a distribution is skewed to the left, the median will always be
- A. Less than the mean.
- B. Between the mean and the mode.
- C. Greater than the mode.
- D. An average of the mean and the mode.
正解: B
質問 23
The following measurements for a sample with dimension X are representative of a process known to be in statistical control
42, 52, 64, 45, 53, 56, 70, 57, 49, 62
Which of the following values BEST approximates the upper and lower control limits of the process capability.
- A. 59 and 51
- B. 64 and 46
- C. 70 and 42
- D. 81 and 29
正解: D
質問 24
What distribution is used to determine the OC curve for an attributes sampling plan?
- A. Normal.
- B. The binomial or the hypergeometric distribution.
- C. Binomial.
- D. Exponential.
正解: B
質問 25
A quality control program is considered to be
- A. A system of activities to provide quality of products and service.
- B. A step by step listing of all quality control check points.
- C. A collection of quality control procedures and guidelines.
- D. A summary of company quality control policies.
正解: A
質問 26
Regardless of the distribution of the individuals, the distribution of the average of n samples will follow which distribution as n becomes large?
- A. Normal
- B. Exponential.
- C. Poisson.
- D. Lognormal.
正解: A
質問 27
A lot is known to be 1.2% defective. Five units are randomly selected from the lot, and the lot is accepted if
1 or fewer defects are found. What is the probability of the lot being rejected?
- A. 0.00223
- B. 0.9985
- C. 0.01
- D. 0.00173
正解: D
質問 28
A comprehensive corrective action program is initiated at a large company. Input for CARs are received from customers, internal and external audits, material review reports and other sources. Which two of the following groups would usually administer and control the CAR process?
I. Management review team.
II. Quality department.
III. Corrective Action Board.
IV. Material Review Board.
- A. I and II only
- B. I and III only
- C. III and IV only
- D. II and III only
正解: B
質問 29
The expression below is which of the following?
- A. General term for the hypergeometric distribution.
- B. General term for the Pascal distribution.
- C. General term for the Poisson distribution.
- D. General term for the binomial distribution.
正解: D
質問 30
Four ingredients are blended to make a final product. Using the data below, what is the expected weight and variation of the final product?
Ingredient A 70 +- 3.00 grams
Ingredient B 20 +- 1.73 grams
Ingredient C 15 +- 1.73 grams
Ingredient D 10 +-- 1.00 grams
- A. 115 +- 7.46 grams
- B. 115 +- 4.00 grams
- C. 115 +- 5.73 grams
- D. 115 +- 3.61 grams
正解: B
質問 31
The ideal results of a quality training effort would NOT include which of the following?
- A. Increased cost-of-quality results.
- B. Reduced defects and employee turn-over.
- C. Increased productivity and job satisfaction.
- D. Improved working methods and morale.
正解: A
質問 32
When asked to make recommendations on how to correct any deficiencies noted in the exit report, the auditor(s) should
- A. Offer no specific advice and few suggestions.
- B. Confer with the client first.
- C. Avoid a recommendation in writing but help the auditee of possible.
- D. Make the best recommendation possible.
正解: A
質問 33
Which of the following is the BEST statement to make regarding the relationship between product precision and product production?
- A. With little precision, performance will improve.
- B. With too much precision, production costs increase.
- C. Precision costs and performance are related.
- D. With too little precision, production costs increase.
正解: C
質問 34
......
実際にあるPassTest CQE問題集PDFで100%合格率 保証付き：https://www.passtest.jp/ASQ/CQE-shiken.html
無料ASQ CQE試験問題と解答：https://drive.google.com/open?id=1EF4-XNAxoglAWwig0-xZ845VAccjn1Fw